To secure this Cisco 200-120 audit isnt a difficult job. Youve just got a need for taking certain methods for attaining good success. Ucertify 200-120 accreditation perform content are incredibly useful trying to keep your getting ready quite effective or maybe more for the mark. Were giving 100% certain achievements around 200-120 actual audit and 200-120 with all the assistance of some of our perform audit. Therefore by training some of our 200-120 training content, make your demanded accreditation and attempt to be a perfect This specialist.

2021 Nov ccna 200-120 dumps:

Q201. - (Topic 8) 

Which two statements about using the CHAP authentication mechanism in a PPP link are true? (Choose two.) 

A. CHAP uses a two-way handshake. 

B. CHAP uses a three-way handshake. 

C. CHAP authentication periodically occurs after link establishment. 

D. CHAP authentication passwords are sent in plaintext. 

E. CHAP authentication is performed only upon link establishment. 

F. CHAP has no protection from playback attacks. 

Answer: B,C 

Topic 9, Mixed Questions 


Q202. - (Topic 5) 

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.) 

A. informational 

B. emergency 

C. warning 

D. critical 

E. debug 

F. error 

Answer: B,D,F 


Q203. - (Topic 4) 

Which parameter or parameters are used to calculate OSPF cost in Cisco routers? 

A. Bandwidth 

B. Bandwidth and Delay 

C. Bandwidth, Delay, and MTU 

D. Bandwidth, MTU, Reliability, Delay, and Load 

Answer: A 


Q204. - (Topic 8) 

A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection? 

A. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut 

B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut 

C. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut 

D. Main(config)# interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)# no shut 

Answer: B 


Q205. - (Topic 8) 

Refer to the exhibit. 

In the Frame Relay network, which IP addresses would be assigned to the interfaces with point-to-point PVCs? 

A. DLCI 16: 192.168.10.1 /24 DLCI 17: 192.168.10.1 /24 DLCI 99: 192.168.10.2 /24 DLCI 28: 192.168.10.3 /24 

B. DLCI 16: 192.168.10.1 /24 DLCI 17: 192.168.11.1 /24 DLCI 99: 192.168.12.1 /24 DLCI 28: 192.168.13.1 /24 

C. DLCI 16: 192.168.10.1 /24 DLCI 17: 192.168.11.1 /24 DLCI 99: 192.168.10.2 /24 DLCI 28: 192.168.11.2 /24 

D. DLCI 16: 192.168.10.1 /24 DLCI 17: 192.168.10.2 /24 DLCI 99: 192.168.10.3 /24 DLCI 28: 192.168.10.4 /24 

Answer: C 


Improved cisco ccna routing and switching 200-120 pdf free download:

Q206. - (Topic 1) 

Where does routing occur within the DoD TCP/IP reference model? 

A. application 

B. internet 

C. network 

D. transport 

Answer: B 


Q207. - (Topic 5) 

Refer to the exhibit. 

What statement is true of the configuration for this network? 

A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported. 

B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown. 

C. The number 1 referred to in the ip nat inside source command references access-list number 1. 

D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24. 

Answer: C 


Q208. - (Topic 6) 

What can be done to secure the virtual terminal interfaces on a router? (Choose two.) 

A. Administratively shut down the interface. 

B. Physically secure the interface. 

C. Create an access list and apply it to the virtual terminal interfaces with the access-group command. 

D. Configure a virtual terminal password and login process. 

E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command. 

Answer: D,E 


Q209. DRAG DROP - (Topic 1) 

Answer: 


Q210. - (Topic 4) 

Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.) 

Router(config)# router ospf 1 

A. All OSPF routers in an area must have the same process ID. 

B. Only one process number can be used on the same router. 

C. Different process identifiers can be used to run multiple OSPF processes 

D. The process number can be any number from 1 to 65,535. 

E. Hello packets are sent to each neighbor to determine the processor identifier. 

Answer: C,D