we provide Exact Cisco ccna 200 125 ebook free practice test which are the best for clearing ccna 200 125 book test, and to get certified by Cisco CCNA Cisco Certified Network Associate CCNA (v3.0). The ccna 200 125 study guide Questions & Answers covers all the knowledge points of the real ccna 200 125 pdf exam. Crack your Cisco cisco ccna 200 125 Exam with latest dumps, guaranteed!
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-125-exam-dumps.html
P.S. Exact 200-125 prep are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials
New Cisco 200-125 Exam Dumps Collection (Question 2 - Question 11)
New Questions 2
which statement about recovering a password on a cisco router is true ?
A. it requires physical access to the router
B. the default reset password is cisco
C. a factory reset is required if you forget the password
D. it requires a secure SSL/VPN connection
Answer: A
New Questions 3
Refer to the exhibit,
which command do you enter so that R1 advertises the loopback0 interface to the BGP peers?
A. network 172.16.1.32 mask 255.255.255.224
B. network 172.16.1.0 0.0.0.0.255
C. network 172.16.1.32 255.255.255.224
D. network 172.16.1.33 mask 255.255.255.224
E. network 172.16.1.32 mask 0.0.0.31
F. network 172.16.1.32 0.0.0.31
Answer: A
New Questions 4
Which two protocols can detect native vlan mismatch errors?
A. STP
B. Cisco Discovery Protocol
C. VTP
D. DTP
E. PAgP
Answer: B,C
New Questions 5
Which value is used to determine the active router in an HSRP default configuration ?
A. router tracking number
B. router IP address
C. router priority
D. router loopback address
Answer: C
New Questions 6
Which command must you enter to enable OSPFv2 in an IPv4 network ?
A. ip ospf hello-interval seconds
B. router ospfv2 process-id
C. router ospf value
D. router ospf process-id
Answer: D
New Questions 7
which two statements about vtp are true ?
A. all switches must be configured with the same VTP domain name
B. all switches must be configured with a unique vtp domain name
C. all switches must be configured to perform trunk negotiation
D. all switches must use the same VTP Version
E. The VTP Server must have the highest revision number in the domain
Answer: A,D
New Questions 8
Which command can you use to test whether a switch supports secure connections and strong authentication?
A. Switch>ssh u2013v 1-I admin 10.1.1.1
B. Router#ssh u2013v1 u2013I admin 10.1.1.1
C. Router>ssh u2013V2 u2013I admin 10.1.1.1
D. Switch#ssh u2013I admin 10.1.1.1
Answer: C
New Questions 9
Which command can you enter to determine whether a switch is operating in trunking mode?
A. show ip interface brief
B. show vlan
C. show interfaces
D. show interface switchport
Answer: D
New Questions 10
Which networking Technology is currently recognized as the standard for computer networking?
A. System network architecture
B. Transmission control protocol/Internet protocol
C. Open system Interconnect
D. Open network architecture
Answer: B
New Questions 11
CORRECT TEXTScenario:
You work as Junior Network Engineer for RADO Network Ltd company. Your colleague has set up a Layer 2 network for testing purpose in one of your client locations. You must verify the configuration and fix if any issues identified as per customer requirements.
Topology Details
- Three switches (SVV1. SW2, and SW3) are connected using Ethernet link as shown in the topology diagram.
- Server1 and PC1 are connected to SW1 and are assigned to VLAN 500 and VLAN 600 respectively.
- Server2 and PC2 are connected to SW2 and are assigned to VLAN 500 and VLAN 600 respectively.
- PC3 is connected to SW3 and assigned to VLAN 600.
Customer requirements
- Verify if switch ports are assigned in correct VLANs as per topology diagram Identify and fix any misconfigurations found in three switches.
- Verify if trunk links are operational between switches and the IEEE 802.1 q trunk encapsulation method is used Identrfy and fix if any misconfigurations are found in the trunk configuration
- You must make sure the ports connected between switches are set as trunk ports.
Special Note: To gain the maximum number you must make sure that VLANs are assigned to switch ports as per customer requirements and make sure the trunk links are operational between switches Do not change VLAN names and VLAN number that are already configured in the switches
Answer:
See the explanation below:
Explanation:
Switch 1 port E0/1 WAS CONNECTED TO A COMPUTER WITH A STRAIGHT THROUGH CABLE AND AS WELL AS ROLLOVER CABLE (FOR CONFIGURATION OF SWITCH PORTS ON THIS SWITCH) WHICH WAS SHOWN IN VLAN 600 IN THE DIAGRAM BUT ACTUALLY THAT PC WAS NOT IN VLAN 600 AFTER CHECKING THE VLAN CONFIGURATION USING SHOW VLAN COMMAND. INSTEAD THIS PORT WAS CONFIGURED IN VLAN 1. SO WE NEEDED TO PUT THAT PC IN VAN 600 USING FOLLOWING COMMANDS-SW1(CONFIG)# INTERFACE E0/0SW1(CONFIG- IF)#SWITCHPORT MODE ACCESSSW1(CONFIG-IF)#SWITCHPORT ACCESS VLAN 600
NOW THE E0/0-PORT OF THIS SWITCH-SW1 WAS RECEIVING NATIVE VLAN MISMATCH FROM SW3 SWITCH-PORT E0/1. ALSO E0/0 OF SW1 AND E0/1 OF SW3 WERE NOT IN TRUNKING MODE. AND THE QUESTION WAS ASKED TO MAKE SURE THAT CONNECTION BETWEEN BOTH SWITCHES SHOULD BE IN TRUNKING MODE WITH 802.1Q ENCAPSULATION ENABLEDSO USED THE BELOW COMMANDS- SW1(CONFIG)#INT E0/0SW1(CONFIG-IF)#SWITCHPORT TRUNK ENCAPSULATION DOT1QSW1(CONFIG-IF)# SWITCHPORT MODE TRUNK.
ON OTHER SWITCH WHICH IS SWITCH3
SW3(CONFIG)#INT E0/0SW3(CONFIG-IF)#SWITCHPORT TRUNK ENCAPSULATION DOT1QSW3(CONFIG-IF)# SWITCHPORT MODE TRUNK.SW3(CONFIG-IF)# SWITCHPORT TRUNK NATIVE VLAN 1
ALSO PORT E0/2 OF SW3 WAS CONNECTED TO SERVER AND IN VLAN 600 AND PORT E0/3 WAS ASSIGNED TO VLAN 500 AND TO A COMPUTER AGAIN IN VLAN 500 ITSELF. SO THAT COMPUTER HAD A CONSOLE CABLE CONNECTED TO SW3 AS WELL IN ORDER TO CONFIGURE SW3 PORTS AS TRUNK PORTS AND SWITCHPORTS USING THE ABOVE STEPS FOR SW1 WHICH WAS MENTIONED ABOVE.
SIMILARLY SW2 PORT E0/1 PORT WAS CONNECTED TO E0/4 PORT OF SW3 SO AGAIN TRUNK LINK CONFIGURATIONS BETWEEN E0/1 AND E0/4 PORTS BETWEEN TWO SWITCHES NEED TO EB DONE HERE. BUT YOU NEDD NOT TO AGAIN RUN THAT NATIVE VLAN COMMAND CHANGE ON SW3 OR SW2 SINCE ON SW3 WE AKREADY CHANGED IN ABOVE STEP AND IN SW2 ITS FINE IN VLAN 1 ONLY.
A COMPUTER WAS CONNECTED TO PORT E0/2 OF SW2 AND WAS IN VLAN 600 AND E0/3 WAS CONNECTED TIO SERVER WHCH WAS IN VLAN 600 AGAIN. ALSO AGAIN THIS TIME THE COMPUTER WAS CONNECTED TO THE SWITCH USING A CONSOLE CABLE ASWELL TO GIVE YOU CONSOLE ACCESS TO CONFIGURE AND VERIFY THE CONFIGURATIONS ON SW2. SO JUST VERIFY THE ACCESS PORTS ARE CORRECTLY ASSIGNED AND TRUNK PORTS AS WELL USING BELOW
COMMANDS.
100% Up to date Cisco 200-125 Questions & Answers shared by Surepassexam, Get HERE: https://www.surepassexam.com/200-125-exam-dumps.html (New 889 Q&As)