Act now and download your Cisco ccna wireless 200 355 dumps test today! Do not waste time for the worthless Cisco ccna wireless 200 355 pdf tutorials. Download Most recent Cisco Implementing Cisco Wireless Network Fundamentals exam with real questions and answers and begin to learn Cisco ccna wireless 200 355 official cert guide pdf free download with a classic professional.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 200-355 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 200-355 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/200-355-exam-dumps.html
Q11. A network engineer at a retail store needs a wireless deployment that can be easily maintained and verified for PCI compliance. What solution will meet this need with the least work?
A. Cloud
B. Autonomous
C. FlexConnect
D. Centralized
Answer: A
Q12. Refer to the exhibit. In an effort to identify RF characteristics at a customer location, an RF engineer uses the Spectrum Analyzer tool that is shown. Which feature that is native to the Spectrum Analyzer is identified by the exhibit?
A. Real-Time FFT
B. Duty Cycle
C. Max Hold
D. Time Domain
Answer: A
Q13. In setting up the wireless network, it is desired that the DHCP server that is configured in WLC1 provides IP addressing to the WLAN. When devices attempt to join the network, they fail to receive an IP address in the range provided by the DHCP server in WLC1, but they do receive an IP address from the DHCP server in SW1. What is causing this issue?
A. The external DHCP server in SW1 will always be the preferred DHCP server and WLC1 will always be the secondary DHCP server in the WLAN.
B. The DHCP server address for SW1 needs to be removed from the DHCP server configuration in WLC1.
C. The primary DHCP server address in WLC1 is incorrect.
D. The primary DHCP server configured in WLC1 is not enabled.
Answer: D
Q14. An installation uses a 21dBi parabolic dish. It is connected to the 802.11n radio via low loss antenna coax rated at 4dB loss/100 feet. After testing, it has been determined that 2mW of power will be lost in the cable. An EIRP producing 200mW is desired. What should the transmit power be set to?
A. 8mW
B. 3dBm
C. 3.16mW
D. 5mW
Answer: C
Q15. What is an interferer that an engineer may see in Cisco CleanAir?
A. microwave ovens
B. rogue APs
C. malicious clients
D. co-channel interference
Answer: A
Q16. What are four features of WPA? (Choose four.)
A. a larger initialization vector, increased to 48 bits
B. a message integrity check protocol to prevent forgeries
C. authenticated key management using 802.1X
D. support for a key caching mechanism
E. unicast and broadcast key management
F. requires AES-CCMP
Answer: A,B,C,E
Q17. What three configuration options can be executed by navigating to the WCS Administration > AAA menu? (Choose three.)
A. Add a Lobby Ambassador guest
B. Add a LDAP server
C. Add an administrative user
D. Add a MAC address list filter
E. Add a RADIUS server
F. Add a TACAS+ server
Answer: C,E,F
Q18. Which two attributes must be configured to match in order for WLCs to operate in the same mobility group? (Choose two.)
A. mobility domain name
B. virtual IP address
C. service interface address
D. hardware model
E. software version
Answer: A,B
Q19. Old 2.4-GHz wireless laptops are unable to connect. What is the most likely cause of this problem?
A. WLAN > General properties are incorrectly configured.
B. WLAN > QoS properties are incorrectly configured.
C. WLAN > Security properties are incorrectly configured.
D. WLAN > Advanced properties are incorrectly configured.
E. Wireless > AP > 802.11 b/g/n AP is incorrectly configured.
F. Wireless > AP > 802.11 b/g/n > Network is incorrectly configured.
Answer: F
Q20. What tool can be used to increase accuracy of WCS heat maps?
A. Map Editor
B. Planning Tool
C. CleanAir
D. Cisco Spectrum Expert
Answer: A