Testking.com will provide you with everything you have to prepare for your Cisco 200-601 actual exam. The particular Cisco 200-601 practice questions and answers are researched and developed by the specialized IT experts. Testkings Cisco Cisco exam demos will help you find certified as well as save the time and money. We provide any discounted price with regard to all the Cisco exam products. So start right away and get the actual Cisco certification as quickly as probable.
2021 Dec 200-601 torrent
Q11. Refer to the exhibit.
NAT has been configured on the router 'GW' and the IP addresses of router 'GW' have been configured properly. Users of PC1 and PC2 are able to ping the IP address
198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem?
A. ip access-list extended ACL_OUTBOUND permit ip 10.1.1.0 0.0.0.255 any
interface Ethernet1 ip access-group ACL_OUTBOUND out
B. interface Ethernet1 ip nat outside
C. interface Ethernet0 ip nat inside
D. ip route 0.0.0.0 0.0.0.0 198.51.100.1
Answer: D
Q12. Which statement is correct regarding Media Redundancy Protocol (MRP) in a ring of ProfiNET devices?
A. When a link fault is detected, MRP rings must converge in less than 100 milliseconds
B. MRP defines two device roles, Media Redundancy Master and Media Redundancy Client
C. MRP can support rings of up to 250 devices
D. MRP is only supported on network switches
Answer: B
Q13. Which statement is true regarding ProfiSAFE?
A. ProfiSAFE traffic must be carried on a network that is physically.separated from automation traffic
B. ProfiSAFE relies on the error detection mechanisms of Ethernet and TCP/IP to determine if there are network errors
C. ProfiSAFE can be used in safety applications up to Safety Integrity Level 3 (SIL3)
D. ProfiSAFE is only used by ProfiBUS PA and ProfiBUS DA devices
Answer: C
Q14. Which in-depth approach is used when deploying defense in an industrial zone?
A. Besides using a dedicated firewall / DMZ construction use an IOS based firewall on the WAN router connecting the industrial site to the Internet.
B. Use NTP to make sure that time stamps of log messages are synchronized such that you can do root cause analysis.
C. Deploy an IDS solution with knowledge about industrial protocols in the industrial zone in combination with a firewall.
D. Use multiple firewalls from different vendors in such a way that network traffic will have to traverse both firewalls so that security holes of one firewall is caught by the other firewall.
Answer: C
Q15. Refer to the exhibit.
SW1, SW2 and virtual switch are connected in a loop. SW1 and SW2 are standard layer-2 switches. Which loop prevention mechanism is best suited for use within this topology?
A. Per-VLAN Rapid Spanning Tree Protocol+
B. End-Host Mode
C. Multi-chassis EtherChannel
D. BPDU Guard
Answer: B
Up to the immediate present 200-601 practice exam:
Q16. You are called at home at 3am by an unskilled machine operator with a suspected network related problem; the controller LEDs are all normal but the output module's
communications LED is not on. The operator has verfied the cable is functional and correctly connected from the communication module to the switch. What is the next check that you ask the unskilled machine operator to make?
A. Log onto the switch using the console port and check that IGMP snooping is enabled
B. Open wireshark and check whether the controller is issuing a forward open instruction to the device
C. Open the diagnostic faceplate on the HMI for the control panel switch and check that the relevant ports are enabled and not in alarm
D. Open Studio 5000 and check the module status tab for the affected output module
Answer: C
Q17. Which two actions are examples of network device hardening for Cisco Industrial Ethernet Switches? (Choose two)
A. Disable unused services
B. Shutdown network ports which are not in use
C. Only allow administrative access using Telnet
D. Deploy IP67 versions of Cisco Industrial Ethernet Switches
E. Set the native VLAN on all trunk ports to VLAN 1
Answer: A,B
Q18. Which five are characteristics that describe Cisco Industrial switches? (Choose five)
A. Din rail mount
B. 19 inch rack mount
C. Fanless
D. Fans
E. Swappable SD flash card
F. Alarm relay
G. -5oC to 45oC operating environment
H. ProfiNET conformance class C compliance
Answer: A,B,C,E,F
Q19. Which describes the relationship between a workgroup bridge?
A. Wired clients of a workgroup bridge can communicate, through the workgroup bridge, with wireless clients of an autonomous or a controller-based access point
B. Wireless clients of a controller-based AP can communicate, through the workgroup bridge, with wireless clients of an autonomous access point
C. Wireless clients of an autonomous access point can communicate with wired clients of a workgroup bridge, but Wireless clients of a controller-based access point cannot communicate with wired clients of a workgroup bridge
D. Wireless clients of a controller-based access point can communicate with wired clients of a workgroup bridge, but Wireless clients of an autonomous access point cannot communicate with wired clients of a workgroup bridge
Answer: A
Q20. Which is an issue with running CIP Motion on a REP network and identifies an alternate resiliency protocol that works for CIP Motion?
A. CIP Motion requires a star topology which is not supported by REP. DLR is a suitable resiliency protocol for CIP motion.
B. REP convergence is not fast enough. DLR is a suitable resiliency protocol for CIP motion.
C. CIP Motion requires a star topology which is not supported by REP. RPVST+.is a suitable resiliency protocol for CIP motion.
D. REP convergence is not fast enough. RPVST+.is a suitable resiliency protocol for CIP motion.
Answer: B