It is impossible to pass Cisco 300 075 ciptv2 exam without any help in the short term. Come to Ucertify soon and find the most advanced, correct and guaranteed Cisco 300 075 vce practice questions. You will get a surprising result by our Down to date Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) practice guides.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 300-075 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 300-075 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/300-075-exam-dumps.html

Q61. When an incoming PSTN call arrives at an MGCP gateway, how does the called number get normalized to an internal directory number in Cisco Unified Communications Manager? 

A. Normalization is done by configuring the significant digits for inbound calls on the MGCP gateway. 

B. Normalization is done using route patterns. 

C. Normalization is done using the gateway incoming called party prefixes based on number type. 

D. Normalization is done using the gateway incoming calling party prefixes based on number type. 

E. Normalization is achieved by local route group that is assigned to the MGCP gateway. 

Answer: A 


Q62. Refer to the exhibit. 

Assume that the HQ phones have access to the HQ partition, and BR phones have access to the BR partition. Which set of implementations would best address the overlapping directory number extensions for intersite (WAN) calling between the HQ site and the BR site? 

A. Configure a route pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Configure the called party DDI of Predot.Configure a route pattern for site BR 8111.[1-3]XXX, and assign it to partition BR. Configure called party DDI Predot.Use the local gateway at each site. Prefix the appropriate site code for the calling number. 

B. Configure a single route pattern for both sites 8[12,12,12].[1-32]XXX. Use a route list that contains the local route group for each site. Prefix the appropriate site code for the calling number. 

C. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number. 

D. Configure a translation pattern 8222.[12]XXX for site HQ, and assign it to partition BR. Use a CSS that contains the partitions for HQ phones.Configure a translation pattern 8111.[1-3]XXX for site BR, and assign it to partition HQ. Use a CSS that contains the partitions for BR phones.For both translation patterns, configure the called party DDI of Predot. Prefix the appropriate site code for the calling number. 

Answer: C 


Q63. Refer to the exhibit. 

To permit three G.729 calls, what should the bandwidth value be for the ip rsvp bandwidth command? 

A. 32 

B. 48 

C. 64 

D. 88 

E. 128 

Answer: D 


Q64. Refer to the exhibit. 

The HQ site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number. Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit. 

What should the AAR group prefix be? 

A. 9 

B. 91 

C. none 

D. + 

E. +1 

Answer: C 


Q65. How is a SIP trunk in Cisco Unified Communications Manager configured for SIP precondition? 

A. The configuration is done by selecting a SIP precondition trunk for trunk type. 

B. The configuration is automatically selected when RSVP is enabled for the location assigned to the trunk. 

C. SIP precondition is configured by selecting E2E for RSVP over SIP on the default SIP profile assigned to the SIP trunk. 

D. SIP precondition is configured by configuring a new SIP profile and selecting E2E for RSVP over SIP. The new SIP profile must then be assigned to the SIP trunk. 

Answer: D 


Q66. On which two call legs is the media encryption enforced in a Collaboration Edge design? (Choose two.) 

A. Expressway-C to Cisco Unified Communications Manager 

B. Expressway-C to Expressway-E 

C. Expressway-E to outside-located endpoint 

D. Expressway-E to Cisco Unified Communications Manager 

E. Expressway-C to internal endpoint 

Answer: B,C 


Q67. Refer to the following exhibit. 

Which Cisco IOS SAF Forwarder configuration is correct? 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

Answer: A 

Explanation: 

Incorrect Answer: B, C, D Summary steps to configure IOS SAF forwarder is given below 

1. enable 

2. configure terminal 

3. router eigrp virtual-instance-name 

4. service-family {ipv4 | ipv6} [vrf vrf-name] autonomous-system autonomous-system-number 

5. topology base 

6. external-client client_label 

7. exit-sf-topology 

8. exit-service-family

9. exit

10. service-family external-client listen {ipv4 | ipv6} tcp_port_number

11. external-client client-label

12. username user-name

13. password password-name 

14. 


Q68. Refer to the exhibit. 

You have configured transcoder resources in both an IOS router and a Cisco Unified Communications Manager. When you review the configurations in both devices the IP addresses and transcoder names are correct, but the transcoder is failing to register with the Cisco Unified Communications Manager. Which command needs to be edited to allow the transcoder to register properly? 

A. The associate profile and dsp farm profile numbers need to match associate ccm 2 command. 

B. The associate ccm 2 priority 1 command needs to be changed so the ccm value matches identifier 1 in the sccp ccm 10.1.1.1 command. 

C. The sccp ccm group number needs to match the associate ccm 2 command. 

D. The maximum sessions command must match the number of codecs configured under the dsp farm profile. 

E. The sccp ccm group number must match the voice-card number. 

Answer: B 

Explanation: 

Incorrect Answer: A, C, D, E The value of the IP address should match the IP address in the ip source-address command Link: 

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmevtr ns.html 


Q69. Which statement is correct about AAR? 

A. The end users see, "Network Congestion Rerouting?" but AAR is otherwise transparent to the end user and works without user intervention. 

B. AAR will display "not enough bandwidth" on the IP phone while it reroutes the call. 

C. AAR allows calls to be rerouted because of insufficient Cisco Unified Border Element controlled bandwidth to an ITSP. 

D. AAR allows calls to be rerouted due to insufficient gatekeeper controlled IP WAN bandwidth. 

Answer: A 

Explanation: 

Incorrect Answer: B, C, D Automated alternate routing (AAR) provides a mechanism to reroute calls through the PSTN or other network by using an alternate number when Cisco Unified Communications Manager blocks a call due to insufficient location bandwidth. With automated alternate routing, the caller does not need to hang up and redial the called party. Link: http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/8_6_1/ccmcfg/b03aar.ht ml 


Q70. In the case of a VCS cluster, which configuration element is recommended for endpoint H.323 registration? 

A. DNS SRV records pointing to the VCS cluster name 

B. static IP addresses 

C. hostname of the VCS cluster configuration master 

D. hostname of the VCS cluster member peer 

Answer: A