Top Quality of 300-115 exam answers materials and preparation labs for Cisco certification for consumer, Real Success Guaranteed with Updated 300-115 pdf dumps vce Materials. 100% PASS Implementing Cisco IP Switched Networks exam Today!
2021 Dec cisco ccnp 300-115 book:
Q31. Refer to the exhibit.
When a network administrator is attempting an SSH connection to the device, in which order does the device check the login credentials?
A. RADIUS server, local username, line password
B. RADIUS server, line password, local username
C. Line password, local username, RADIUS server
D. Line password, RADIUS server, local username
Answer: A
Q32. Which switch feature prevents traffic on a LAN from being overwhelmed by continuous multicast or broadcast traffic?
A. storm control
B. port security
C. VTP pruning
D. VLAN trunking
Answer: A
Q33. Refer to the exhibit.
Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?
A. Switch B is configured in transparent mode.
B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.
C. The VTP revision number of the Switch B is higher than that of Switch A.
D. The trunk between Switch A and Switch B is misconfigured.
Answer: A
Q34. In a Cisco switch, what is the default period of time after which a MAC address ages out and is discarded?
A. 100 seconds
B. 180 seconds
C. 300 seconds
D. 600 seconds
Answer: C
Q35. An EtherChannel bundle has been established between a Cisco switch and a corporate web server. The network administrator noticed that only one of the EtherChannel links is being utilized to reach the web server. What should be done on the Cisco switch to allow for better EtherChannel utilization to the corporate web server?
A. Enable Cisco Express Forwarding to allow for more effective traffic sharing over the EtherChannel bundle.
B. Adjust the EtherChannel load-balancing method based on destination IP addresses.
C. Disable spanning tree on all interfaces that are participating in the EtherChannel bundle.
D. Use link-state tracking to allow for improved load balancing of traffic upon link failure to the server.
E. Adjust the EtherChannel load-balancing method based on source IP addresses.
Answer: E
Most up-to-date cbt nuggets ccnp routing and switching 300-115 switch:
Q36. A network engineer changed the port speed and duplex setting of an existing EtherChannel bundle that uses the PAgP protocol. Which statement describes what happens to all ports in the bundle?
A. PAgP changes the port speed and duplex for all ports in the bundle.
B. PAgP drops the ports that do not match the configuration.
C. PAgP does not change the port speed and duplex for all ports in the bundle until the switch is rebooted.
D. PAgP changes the port speed but not the duplex for all ports in the bundle.
Answer: A
Q37. Which statement describes what happens when a port configured with root guard receives a superior BPDU?
A. The port goes into errdisabled state and stops forwarding traffic.
B. The port goes into BPDU-inconsistent state and stops forwarding traffic.
C. The port goes into loop-inconsistent state and stops forwarding traffic.
D. The port goes into root-inconsistent state and stops forwarding traffic.
Answer: D
Q38. Several new switches have been added to the existing network as VTP clients. All of the new switches have been configured with the same VTP domain, password, and version. However, VLANs are not passing from the VTP server (existing network) to the VTP clients. What must be done to fix this?
A. Remove the VTP domain name from all switches with "null" and then replace it with the new domain name.
B. Configure a different native VLAN on all new switches that are configured as VTP clients.
C. Provision one of the new switches to be the VTP server and duplicate information from the existing network.
D. Ensure that all switch interconnects are configured as trunks to allow VTP information to be transferred.
Answer: D
Q39. What happens on a Cisco switch that runs Cisco IOS when an RSTP-configured switch receives 802.1d BPDU?
A. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives an 802.1d BPDU, it responds with an 802.1d BPDU and eventually the two switches run 802.1d to communicate.
B. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it responds with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
C. 802.1d does not understand RSTP BPDUs because they are different versions, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU.
D. 802.1d understands RSTP BPDUs because they are the same version, but when a RSTP switch receives a 802.1d BPDU, it does not respond with a 802.1d BPDU and eventually the two switches run 802.1d to communicate.
Answer: A
Q40. After port security is deployed throughout an enterprise campus, the network team has been overwhelmed with port reset requests. They decide to configure the network to automate the process of re-enabling user ports. Which command accomplishes this task?
A. switch(config)# errdisable recovery interval 180
B. switch(config)# errdisable recovery cause psecure-violation
C. switch(config)# switchport port-security protect
D. switch(config)# switchport port-security aging type inactivity
E. switch(config)# errdisable recovery cause security-violation
Answer: B