Cause all that matters here is passing the Cisco 300-625 exam. Cause all that you need is a high score of 300-625 Implementing Cisco Storage Area Networking (DCSAN) exam. The only one thing you need to do is downloading Pass4sure 300-625 exam study guides now. We will not let you down with our money-back guarantee.
Cisco 300-625 Free Dumps Questions Online, Read and Test Now.
NEW QUESTION 1
Refer to the exhibit.
What is the result of the configuration?
- A. No-drop CoS values are advertised by the DCBX.
- B. LFC is prioritized over PFC on Ethernet 1/10.
- C. PFC operates on Ethernet 1/10 regardless of the capability of the peer.
- D. PFC fails to operate properly unless LFC is disabled on Ethernet 1/10.
Answer: A
NEW QUESTION 2
Refer to the exhibit.
A port channel has been configured between a Cisco MDS and a Cisco Fabric Interconnect switch. Which interface(s) in the port channel carry the control plane traffic?
- A. per packet, balanced between interfaces fc1/9 and fc1/10
- B. from interface fc1/9
- C. from interface fc1/10
- D. per flow, balanced between interfaces fc1/9 and fc1/10
Answer: D
NEW QUESTION 3
Which configuration is available only in Cisco DCNM-SAN Advanced mode?
- A. IVR
- B. VMpath configuration
- C. zoning
- D. template-based provisioning
Answer: A
NEW QUESTION 4
DRAG DROP
Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.
Select and Place:
- A. Mastered
- B. Not Mastered
Answer: A
NEW QUESTION 5
Refer to the exhibits.
A storage network engineer activates a zoneset on MDS-A and verifies the successful activation (Exhibit 1). The engineer is then notified that there is a SAN outage (Exhibit 2) What is the cause of the outage?
- A. Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
- B. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.
- C. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric.
- D. Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric.
Answer: D
NEW QUESTION 6
A storage administrator is enabling DH-CHAP for the first time on a Fibre Channel fabric. Which condition must the administrator consider while configuring this feature?
- A. NTP must be configured on all devices or the configuration fails.
- B. The MD5 hash must be used if TACACS+ or RADIUS authentication for FCSP is enabled.
- C. All switches on the fabric must be configured for the same password.
- D. Enabling DH-CHAP protocol feature is unsupported on FCIP interfaces.
Answer: B
NEW QUESTION 7
A storage administrator wants to enable NPV in a Fibre Channel edge switch. Which configuration is supported in this mode?
- A. Cisco Fabric Services distribution over Fibre Channel
- B. E Port connectivity to the core switch
- C. local switching of east-west traffic
- D. Dynamic Port VSAN Membership
Answer: A
NEW QUESTION 8
A storage administrator manually configures a storage switch to use a new static domain ID. After issuing an fcdomain restart vsan 1 command, the administrator sees that the switch is still using the existing domain ID. What is the reason why the configuration is not working?
- A. Static domain IDs apply only after a switch is rebooted.
- B. The disruptive keyword was not used on the command.
- C. Build fabric notifications were not sent to the other switches.
- D. Domain manager fast restart is not enabled on the switch.
Answer: A
NEW QUESTION 9
What is the effect of a non-graceful virtual machine shutdown on a virtualized server that is connected to a SAN with Fibre Channel interfaces?
- A. NP Port reload connected to the upstream SAN switch
- B. out-of-service Fibre Channel interfaces on the SAN switch
- C. frames stuck in the storage system
- D. frames stuck in the HBA buffer of the server
Answer: B
NEW QUESTION 10
Refer to the exhibit.
Which command is used to determine which switch has the lock?
- A. show zoneset active
- B. show zone status
- C. show flogi database
Answer: C
NEW QUESTION 11
Which port mode is used on an NPV device to connect to an NPIV core switch?
- A. E
- B. F
- C. N
- D. NP
Answer: D
NEW QUESTION 12
Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?
- A. The autoreconfigure option is disabled on both switches.
- B. The autoreconfigure option is enabled on both switches.
- C. The rcf-reject option is enabled on the interfaces.
- D. The rcf-reject option is disabled on the interfaces.
Answer: A
NEW QUESTION 13
A storage administrator is connecting two previously configured switches to make a single fabric. When the E Ports are connected, the administrator sees a ZONE MERGE FAILURE message referring to the zoneset for VSAN 10 on each switch. Which command should the administrator use to allow these switches to work together?
- A. zoneset import interface fc1/1 vsan 10
- B. zoneset distribute full vsan 10
- C. zoneset overwrite-control vsan 10
- D. zoneset copy active-zoneset full-zoneset
Answer: A
NEW QUESTION 14
A storage network engineer must configure a 48-port Cisco MDS switch to reject any login requests to VSAN 10 from unauthorized Fibre Channel devices and switches. All the devices that were already logged in to the switch from this VSAN must be allowed without any manual configuration. Which configuration must be applied?
- A. switch(config)# feature port-security switch(config)# port- security activate vsan 10
- B. switch(config)# feature port- security switch(config)# port-security activate vsan 10 no auto- learn
- C. switch(config)# feature port-security switch(config)# port-security database vsan 10 switch(config-port-security)# any-wwn interface fc1/1 – fc1/48
- D. switch(config)# port-security activate vsan 10
Answer: D
NEW QUESTION 15
Refer to the exhibit.
An engineer is configuring Inter-VSAN routing for two Cisco MDS switches. The FSPF cost between the switches is 500, and the Cisco MDS core virtualizes an IVR NAT domain as shown. Which statement about the topology is correct?
- A. The MDS-Core simulates an IVR NAT, and the FSPF cost is 500.
- B. The MDS-Core simulates an IVR NAT, and increases the cost to 501.
- C. The MDS-Core simulates an IVR NAT, and decreases the cost to 400.
- D. The MDS-Core simulates an IVR NAT, and increases the cost to 600.
Answer: B
NEW QUESTION 16
Which action must be performed to deactivate a VSAN without losing its configuration?
- A. Isolate it.
- B. Delete it.
- C. Rename it.
- D. Suspend it.
Answer: D
NEW QUESTION 17
Refer to the exhibit.
Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?
- A. device-alias mode
- B. session
- C. qos
- D. smart-zoning
Answer: A
NEW QUESTION 18
Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?
- A. MDS(config)# interface fc 1/1MDS(config-if)# fcsp esp manual
- B. MDS(config)# fcsp esp manual
- C. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp mode gcm MDS(config-if-fcsp)# fcsp esp manual
- D. MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual MDS(config-if-fcsp)# mode gcm
Answer: A
NEW QUESTION 19
DRAG DROP
Drag and drop the FLOGI parameters from the left onto the descriptions from which they were-derived on the right.
Select and Place:
- A. Mastered
- B. Not Mastered
Answer: A
NEW QUESTION 20
After user account attributes are modified in Cisco NX-OS, when do changes to the user’s session attributes take effect?
- A. immediately
- B. at the scheduled time
- C. when the user logs out of a session
- D. when the user creates a new session
Answer: D
NEW QUESTION 21
A storage administrator is configuring inter-VSAN routing on a fabric that contains duplicate domain IDs. Which feature must be configured to ensure continued operation?
- A. auto topology
- B. transit VSANs
- C. IVR NAT
- D. virtual domains
Answer: C
NEW QUESTION 22
A storage network engineer must install and configure a new MDS switch in a data center network. Which two statements about available choices during the MDS switch initial setup are correct? (Choose two.)
- A. The engineer can choose what will be the administrator account.
- B. The secure password standard is required.
- C. The engineer can configure the default zone policy.
- D. The engineer can configure the default switch port trunk mode.
- E. The engineer does not have the choice to enable or disable full zoneset distribution.
Answer: AC
NEW QUESTION 23
......
100% Valid and Newest Version 300-625 Questions & Answers shared by Thedumpscentre.com, Get Full Dumps HERE: https://www.thedumpscentre.com/300-625-dumps/ (New 0 Q&As)