What Exact HPE0-S58 Test Preparation Is

NEW QUESTION 1
Match each interconnect device with its appropriate use case.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:
References: https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c05385134 https://h20215.www2.hpe.com/v2/GetPDF.aspx/c04815127.pdf

NEW QUESTION 2
An integrator needs to configure a set of networks for Synergy compute nodes to send data to devices outside of a Synergy frame.
How should the integrator complete the task?

• A. Add the network to an interconnect bay within a Logical Enclosure (LE)
• B. Add the networks to an uplink set within a Logical Interconnect Group (LIG)
• C. Add the networks to an Enclosure Group (EG)
• D. Add the network sets to a Logical Interconnect Group (LIG)

Answer: A

NEW QUESTION 3
A customer needs to aggregate uplink ports from two Virtual Connect interconnects to increase bandwidth and availability of the networks configured for HPE Synergy platform.
Which steps must the integrator perform in the configuration to meet the customer’s needs?

• A. Connect Satellite modules using Ports L1 and L4
• B. Connect Ports Q7 and Q8 on the Master interconnect Modules (ICM)
• C. Install Redundant Frame Link Modules and a second management ring
• D. Enable Intelligent Resilient Fabric (IRF) on the Virtual Connect Modules

Answer: A

NEW QUESTION 4
A customer is using HPE Synergy Composer to manage the compute module and 3PAR volume attachments.
The datastore attached to the VMware servers has run out of space.
What is the most efficient procedure the integrator should follow to extend the volume with minimum effect on the compute modules?

• A. Set the volume to maintenance mode, and increase the volume in 3PAR SSMC
• B. Increase the capacity of the volume in the combined profile form
• C. Create a snapshot, and increase the capacity of the snapshot directly in the Synergy Composer
• D. Increase the capacity of the volume directly in the Synergy Composer

Answer: D

NEW QUESTION 5
Which tool should an integrator use to determine the power requirements of an HPE Synergy solution?

• A. HPE Product Bulletin
• B. HPE SalesBuilder for Windows
• C. HPE Synergy Planning Tool
• D. HPE SPOCK

Answer: C

NEW QUESTION 6
An integrator has installed a new Synergy frame into a rack with two existing Synergy frames in a customer’s environment.
Click where the integrator should verify that the cabling for the management ring was completed correctly.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 7
A customer with a 3-frame Synergy composable infrastructure has received a second rack to expand existing composable infrastructure resource pools. The integrator has cabled the management ring as shown.
Which steps should the integrator take to increase availability of this configuration (Choose two.)

• A. Move on Composer to Rack 2
• B. Move both Composers to Rack 2
• C. Enable multi-rack high availability in HPE OneView
• D. Move both management uplinks to Rack 2
• E. Move one management uplink to Rack 2

Answer: BE

NEW QUESTION 8
An integrator is installing three Synergy frames in different locations for a customer. As part of the installation, the customer requests a single monitoring dashboard that shows the current hardware status, warranty status, and open support cases of all three frames.
Which configuration steps must the integrator perform to provide the customer with this functionality?

• A. Enable Remote Support and Insight Online Integration in the Composer UI
• B. Install Insight Remote Support Advanced, and integrate it with HPE Global Dashboard
• C. Configure OneView with iLO Amplifier pack
• D. Activate iLO Federation on all installed compute nodes

Answer: C

NEW QUESTION 9
A customer needs to deploy additional management components, such as vCenter Server and HPE Global Dashboard.
According to HPE best practices, how should an integrator deploy these components?

• A. Deploy VMware HA cluster on two dedicated management servers, then deploy management components to this cluster.
• B. Deploy vCenter Server as a virtual machine on the Hyper-V host and HPE Global Dashboard to the domain controller.
• C. Install vCenter Server on the domain controller, then deploy HPE Global Dashboard to the HPE Composer or HPE OneView appliance.
• D. Deploy vCenter Server to any Windows machine, and install HPE Global Dashboard on the same server.

Answer: B

NEW QUESTION 10
A customer has a Hyper-V and ESXi hypervisors deployed on an HPE Synergy platform. The customer needs a tool that will provide health and performance monitoring. Because their environment is very dynamic, the tool should also help them to optimize performance and predict and prevent problems.
Which tool should the customer use?

• A. HPE InfoSight
• B. HPE OneView for vCenter Server
• C. HPE Composer
• D. HPE Global Dashboard

Answer: C

NEW QUESTION 11
An integrator needs to validate whether the datastore created for ESXi systems based on 3PAR virtual volume can support all DRS cluster functionalities.
Click on the parameter that the integrator needs to verify.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 12
Which HPE Synergy D3940 storage module configuration is valid?

• A. a single RAID set to be shared across the SAS fabric to multiple compute nodes as a virtualization host datastore
• B. maximum of three HPE Synergy D3940 storage modules per frame to be used by any compute module within the management ring
• C. any number of the drives from storage module to be mapped to any single compute node
• D. a pair of disks to house Composer backups and Synergy firmware bundles

Answer: A

NEW QUESTION 13
Which component must be deployed at the customer site and is essential for HPE InfoSight for Servers?

• A. HPE Intelligent Provisioning
• B. HPE Global Dashboard
• C. iLO Amplifier Pack
• D. HPE Composer

Answer: C

Explanation:
References: https://www.slideshare.net/Xylos/hpe-infosight-for-servers

NEW QUESTION 14
A Synergy integrator is unable to assign an HPE 3PAR Virtual Volume to a new server profile in HPE Composer. The Virtual Volume has been previously assigned to another profile.
Which setting in HPE Composer is preventing the integrator from assigning the volume to the new profile?

• A. private, in the volume properties
• B. shared, in the volume properties
• C. private, in the storage pool properties
• D. shared, in the storage pool properties

Answer: D

NEW QUESTION 15
A customer has the following configuration: Frame 1
Bay 1 – HPE Synergy 12Gb SAS Connection Module
Bay 2
Bay 3 – HPE Virtual Connect SE 40 GB F8 Module
Bay 4 – HPE Synergy 12GB SAS Connection Module
Bay 5
Bay 6 – HPE Synergy 10 Gb Interconnect Link Module
Frame 2
Bay 1 – HPE Synergy 12Gb SAS Connection Module
Bay 2
Bay 3 – HPE Synergy 10Gb Interconnect Link Module
Bay 4 – HPE Synergy 12Gb SAS Connection Module
Bay 5
Bay 6 – HPE Virtual Connect SE 40Gb F8 Module
How many more frames can the customer add to their Synergy composable fabric? (Note: Enter your answer in the answer field below.)

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:
Frame 1 – Bay 2 – HPE Virtual Connect SE 100Gb F32 Module for Synergy (867796-B21)
Frame 1 – Bay 5 – HPE Virtual Connect SE 16Gb Fibre Channel Module for Synergy (779227-B21)
Frame 2 - Bay 2 – Brocade 16Gb/24 Power Pack+ Fibre Channel SAN Switch Module for HPE Synergy (K2Q86A)
Frame 2 – Bay 5 – HPE Synergy 4820C 10/20/25Gb Converged Network Adapter (876449-B21)

NEW QUESTION 16
A customer has two Synergy frames using HPE Virtual Connect and 20Gb satellite modules linked together. What is the maximum number of frames that can be added to this configuration? (Note: Enter your answer in the answer field below.)

• A. 3

Answer: A

Explanation:
\ 3 (three) frames maximum

NEW QUESTION 17
A customer needs to expand a single-frame Synergy solution to two frames.
What should the integrator do to establish a proper management network for the two frames?

• A. Connect the RJ-45 management ports of the Virtual Connect modules together with redundant CAT6Acables.
• B. Disconnect the existing management ring, and cable the Frame Link Modules in the first frame to the Frame Link Modules in the added frame.
• C. Connect the RJ-45 front panel connectors on the two frames together with a single CAT6A cable.
• D. In the Synergy console, select the Frame Link Modules in the new frame and define the connection between them.

Answer: D

NEW QUESTION 18
What does the hypervisor cluster profile feature of HPE OneView enable the integrator to accomplish?

• A. configure a DRS cluster that provides load balancing functionality
• B. enable Adaptive Optimization using SSMC that will optimize VM location
• C. enable load balancing policies for the most important VMs using vCenter Server and traffic shaping policies
• D. use the CPU affinity option to improve CPU scheduling

Answer: A

NEW QUESTION 19
A customer is planning to deploy OneView for vCenter Server to improve management procedures for growing virtualization environment. The customer is concerned about resources required by HPE OneView for vCenter Server.
Which statement about deploying HPE OneView for vCenter Server is true?

• A. It is deployed as an application on the Windows Server machine with at least 48GB of memory.
• B. It is deployed as a part of the HPE Composer installation.
• C. It is deployed as a virtual machine on the supported hypervisor.
• D. It can only be deployed if HPE Global Dashboard is already installed.

Answer: C

NEW QUESTION 20
An integrator is creating a server profile template for a VMware Cluster in a Synergy environment. The network administrator has given the server team two 40Gb uplinks with all 200 VLANs presented.
Click the appropriate network type that the integrator should select.

• A. Mastered
• B. Not Mastered

Answer: A

Explanation:

NEW QUESTION 21
A customer has a datacenter with 3-frame Master/Satellite Synergy solution. They plan to add two additional frames to the remote datacenter, but they want to have a single management tool.
How should the integrator set up the management of the datacenter?

• A. Add two frames from the remote datacenter as remote enclosures using existing Composer
• B. Install one Composer in every frame in both local and remote datacenter
• C. Deploy one Composer in each site and link them together
• D. Connect the management links with fibre cables if the distance between datacenters is more than 500m

Answer: A

NEW QUESTION 22
A customer is planning an HPE Synergy solution with 20 frames and needs to minimize the number of management ports that are required to connect the frames into the existing management network.
Which procedure should the integrator use to address the customer’s concern?

• A. Connect the RJ-45 front ports of each frame to an external switc
• B. Then, connect the uplink from the external switch into the customer’s management network.
• C. Connect FLMs from all frames to two external switches for redundanc
• D. Then, connect the two uplinks from the two switches into the customer’s management network.
• E. Connect the RJ-45 front ports of each frame to two external switches for redundanc
• F. Then, connect the uplink from the two switches into the customer’s management network.
• G. Connect FLMs from all frames into a management rin
• H. Then, connect the management ring to the customer’s management network using two uplinks.

Answer: D

NEW QUESTION 23
A customer wants to add nodes to the existing ESXi cluster using the HPE OneView for vCenter Server. What must be done before this functionality can be used?

• A. The cluster must be imported to HPE OneView
• B. An additional VMkernel port must be created for OneView integration
• C. All local datastores must be disconnected or removed from the other cluster nodes
• D. At least one node of the cluster must be placed in the maintenance mode

Answer: A

NEW QUESTION 24
......