The Up To Date Guide To NS0-184 Braindump

NEW QUESTION 1
You installed a new 2-node FAS500f ONTAP 9.8 switchless cluster that serves NAS volumes to both
NFSv4.1 and SMB clients. The host operating systems have full flow control enabled on their data
ports.
In this scenario, which two flow control settings would you verify? (Choose two.)

• A. Verify thatthedatanetworkportshavefullflowcontroldisabled.
• B. Verifythattheclusternetworkportshavefullflowcontrolenabled.
• C. Verify thatthedatanetworkportshavefullflowcontrolenabled.
• D. Verifythattheclusternetworkportshavefullflowcontroldisabled.

Answer: AB

Explanation:
Reference: https://docs.netapp.com/us-en/ontap/pdfs/sidebar/Network_management.pdf

NEW QUESTION 2
Click the Exhibit button.

After installation of a new ONTAP cluster, you experience a problem. You successfully create a support case on the NetApp Support site. The customer asks you how to view the status of the case.
Referring to the exhibit, which two steps would allow the customer to accomplish this task? (Choose two.)

• A. Open https://support.netapp.com, using the partner credentials.
• B. Open https://support.netapp.com, using the customer credentials.
• C. Open My Cases, and select the 41747189 case number.
• D. Open My Cases, and select Create a Case.

Answer: BC

Explanation:
Reference: https://mysupport.netapp.com/site/info/find-support

NEW QUESTION 3
You want to create a data volume on aggr0 and you receive a message with the following warning:
''Warning: You are about to create a volume on a root aggregate.
This may cause severe performance or stability problems and therefore is not recommended. Do you want
to proceed?''
What is the reason for this severe performance or stability problem?

• A. Controller failover and storage failover are separate processes that must occur in parallel, otherwiseproblems will arise.
• B. The performance load generated by the data volume can be very strong, so it should not be shared withvol0 on aggr0, requiring a separate aggregate for it.
• C. The performance load generated by the vol0 cannot be shared with any other volume on aggr0, requiringa dedicated aggregate for it.
• D. Controller failover and storage failover are separate processes that must occur at different times,otherwise problems will arise.

Answer: B

NEW QUESTION 4
Your customer wants to know more about the network configuration within the cluster.
In this scenario, which statement is correct about a LIF?

• A. A LIF is a port that provides physical connections.
• B. A LIF is created within a broadcast domain and contains a pool of IP address.
• C. A LIF is an IP address or a WWPN that is associated with a port.
• D. A LIF separates network domains to access cluster data.

Answer: C

NEW QUESTION 5
After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP
System Manager regarding SAS HA issues.
In this scenario, which NetApp tool would have identified these errors after the installation process?

• A. Cloud Manager
• B. ONTAP System Manager
• C. Active IQ Config Advisor
• D. Active IQ Unified Manager

Answer: B

NEW QUESTION 6
Data ONTAP 9 supports which three features? (Choose three.)

• A. SMB 3.0
• B. NFSv2
• C. SnapMirror
• D. Infinite Volumes

Answer: ACD

NEW QUESTION 7
After adding two nodes to an FC-enabled cluster, the storage administrator wants to ensure that existing LUNs can use paths on the new nodes.
What is required to complete this task?

• A. Use the storage port rescan command.
• B. Use the lun mapping add-reporting-nodes command.
• C. Use the lun bind create command.
• D. Rescan the bus on the hosts by using the rescan-scsi-bus.sh script.

Answer: AB

NEW QUESTION 8
Which logical interface has a fixed firewall policy?

• A. data LIF
• B. cluster management LIF
• C. cluster LIF
• D. intercluster LIF

Answer: C

Explanation:
Reference: https://docs.netapp.com/usen/
ontap/networking/configure_firewall_policies_for_lifs.html#create-a-firewall-policy-andassigning-
it-to-a-lif

NEW QUESTION 9
You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were
automatically discovered by “automatic port placement”.
In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

• A. routes
• B. IPspaces
• C. broadcast domains
• D. subnets

Answer: AD

NEW QUESTION 10
A customer requires encryption at rest on every node root volume.
In this scenario, which two encryption solutions will fulfill this requirement? (Choose two.)

• A. NSE
• B. NAE
• C. IPsec
• D. NVE

Answer: BD

Explanation:
Reference: https://docs.netapp.com/us-en/ontap/encryption-at-rest/configure-netapp-volumeencryptionconcept.
html#aggregate-level-encryption

NEW QUESTION 11
After the successful installation of a NetApp ONTAP cluster, the customer wants to know how to view
Telemetry data. The customer also wants to receive online information about any risks with the cluster and
potential bestpractice gaps.
Which tool satisfies the customer’s requirements?

• A. Active IQ Digital Advisor
• B. Interoperability Matrix Tool
• C. Spot by NetApp
• D. Cloud Manager

Answer: A

Explanation:
Reference: http://docs.netapp.com/us-en/ontap/pdfs/sidebar/Cluster_administration.pdf

NEW QUESTION 12
An administrator issued the cluster setup command and configured a 2-node ONTAP 9.8 cluster.
In this scenario, which tool would the administrator use to validate the configuration?

• A. Active IQ Upgrade Advisor
• B. Interoperability Matrix Tool
• C. NetAppDocs
• D. Active IQ Config Advisor

Answer: C

NEW QUESTION 13
Click the Exhibit button.

You are preparing to replace a Cisco Nexus 92300YC switch. You have executed the cluster pingclusternode1commandandreceivedtheoutputasshownintheexhibit.
Which two checks indicate that the cluster is ready for the replacement to be performed? (Choose
two.)

• A. 2paths up, 0paths down(TCP check)
• B. 2paths up, 0 paths down(UDP check)
• C. largerthanPMTUcommunicationsucceedson4path(s)
• D. basicconnectivitysucceedson4path(s)

Answer: AD

NEW QUESTION 14
You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster
that uses NetApp CN1610 cluster interconnect switches.
In this scenario, what are two valid actions for this installation? (Choose two.)

• A. Add the new nodes to the existing cluster and switches.
• B. Createanew2-nodeswitchedclusterthatusestheCN1610clusterswitches.
• C. Createanew2-nodeswitchlesscluster.
• D. Migrate the existing cluster to new switches and add the new nodes.

Answer: BD

Explanation:
Reference:
https://kb.netapp.com/Advice_and_Troubleshooting/Flash_Storage/AFF_Series/Controller_Hardwar
e_Upgrade3A_Adding_AFF_A250_nodes_to_existing_cluster_report_HA_interconnect_errors_and_c
annot_perform_takeover

NEW QUESTION 15
YouareusingBroadcomBES-53248switchesforaclusterinterconnectinabaseconfiguration. In
thisscenario,whatistheminimumnumberofISLssupportedbetweentheswitches?

• A. 1
• B. 2
• C. 3
• D. 4

Answer: B

Explanation:
Reference: https://docs.netapp.com/us-en/ontap-systemsswitches/pdfs/sidebar/BES_53248_Switches.pdf (3)

NEW QUESTION 16
You installed two separate clusters in an isolated data center without outbound network
access. The customer wants to troubleshoot issues locally and also create custom Excel reports for
capacity utilization from a local server.
In this scenario, which NetApp tool would satisfy this requirement?

• A. Active IQ Digital Advisor
• B. Cloud Insights
• C. ONTAP System Manager
• D. Active IQ Unified Manager

Answer: D

NEW QUESTION 17
Click the Exhibit button.

While you are introducing the customer to the NetApp Support website, they ask you to ensure that the new ONTAP storage array is covered by support before you complete the knowledge transfer procedure. Referring to the exhibit, which two widgets would you select to accomplish this task?
(Choose two.)

• A. Active IQ
• B. Product Support
• C. Systems
• D. Contracts and Warranties

Answer: CD

NEW QUESTION 18
You are expanding an existing 4-node ONTAP 9.8 cluster with a FAS8300 HA pair by adding a new FAS500f HA pair. Before the expansion, you are asked to save the configuration of the cluster to a backup file.
In this scenario, which two ONTAP configuration backup methods are available? (Choose two.)

• A. storage VM
• B. node
• C. cluster
• D. switch

Answer: AC

Explanation:
Reference: https://docs.netapp.com/us-en/ontap-whatsnew/pdfs/fullsitesidebar/TR_4894NetApp_ONTAP_9_9_1_Feature_Overview.pdf

NEW QUESTION 19
Click the Exhibit button.

What are two functions of the four Ethernet switches in the supported configuration that is shown in the exhibit? (Choose two.)

• A. to provide a direct connection for the SnapMirror Synchronous (SM-S)
• B. to install cross-site cluster management switches
• C. to provide connectivity for NVRAM over iWARP
• D. to enable SyncMirror replication

Answer: AC

NEW QUESTION 20
......