Act now and download your Cisco 100-101 test today! Do not waste time for the worthless Cisco 100-101 tutorials. Download Refresh Cisco CCNA Interconnecting Cisco Networking Devices 1 (ICND1) exam with real questions and answers and begin to learn Cisco 100-101 with a classic professional.

2016 Nov cisco ccna 100-101 pdf:

Q101. What command sequence will configure a router to run OSPF and add network 10.1.1.0 /24 to area 0? 

A. router ospf area 0 network 10.1.1.0 255.255.255.0 area 0 

B. router ospf network 10.1.1.0 0.0.0.255 

C. router ospf 1 network 10.1.1.0 0.0.0.255 area 0 

D. router ospf area 0 network 10.1.1.0 0.0.0.255 area 0 

E. router ospf network 10.1.1.0 255.255.255.0 area 0 

F. router ospf 1 network 10.1.1.0 0.0.0.255 

Answer:


Q102. Refer to the exhibit. 

An administrator cannot connect from R1 to R2. To troubleshoot this problem, the administrator has entered the command shown in the exhibit. Based on the output shown, what could be the problem? 

A. The serial interface is configured for half duplex. 

B. The serial interface does not have a cable attached. 

C. The serial interface has the wrong type of cable attached. 

D. The serial interface is configured for the wrong frame size. 

E. The serial interface has a full buffer. 

Answer:


Q103. Which three approaches can be used while migrating from an IPv4 addressing scheme to an IPv6 scheme? (Choose three) 

A. static mapping of IPv4 address to IPv6 addresses 

B. configuring IPv4 tunnels between IPv6 islands 

C. use DHCPv6 to map IPv4 addresses to IPv6 addresses 

D. use proxying and translation (NAT-PT) to translate IPv6 packets into IPv4 packets 

E. configure IPv6 directly 

F. enable dual-stack routing 

Answer: BDF 


Q104. Identify the four valid IPv6 addresses. (Choose four.) 

A. :: 

B. ::192:168:0:1 

C. 2000:: 

D. 2001:3452:4952:2837:: 

E. 2002:c0a8:101::42 

F. 2003:dead:beef:4dad:23:46:bb:101 

Answer: ABEF 


Q105. Which layer of the TCP/IP stack combines the OSI model physical and data link layers? 

A. Internet layer 

B. transport layer 

C. application layer 

D. network access layer 

Answer:


Replace cisco ccent 100-101 pdf:

Q106. Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.) 

A. router#show version 

B. router#show ip interface 

C. router#show protocols 

D. router#show controllers 

E. router#show running-config 

Answer: BC 


Q107. Refer to the exhibit. 

Why was this message received? 

A. No VTY password has been set. 

B. No enable password has been set. 

C. No console password has been set. 

D. No enable secret password has been set. 

E. The login command has not been set on CON 0 

F. The login command has not been set on the VTY ports. 

Answer:


Q108. Refer to the exhibit. 

Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance? 

A. router1(config)#ip route 1 192.168.201.1 255.255.255.0 192.168.201.2 

B. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 1 

C. router1(config)#ip route 5 192.168.202.0 255.255.255.0 192.168.201.2 

D. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 5 

Answer:


Q109. Refer to the exhibit. 

Why did the device return this message? 

A. The command requires additional options or parameters 

B. There is no show command that starts with ru. 

C. The command is being executed from the wrong router mode. 

D. There is more than one show command that starts with the letters ru. 

Answer:


Q110. Which statements accurately describe CDP? (Choose three.) 

A. CDP is an IEEE standard protocol. 

B. CDP is a Cisco proprietary protocol. 

C. CDP is a datalink layer protocol. 

D. CDP is a network layer protocol. 

E. CDP can discover directly connected neighboring Cisco devices. 

F. CDP can discover Cisco devices that are not directly connected. 

Answer: BCE