It is impossible to pass Cisco 100-105 exam without any help in the short term. Come to Testking soon and find the most advanced, correct and guaranteed Cisco 100-105 practice questions. You will get a surprising result by our Improve Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0) practice guides.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 100-105 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 100-105 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/100-105-exam-dumps.html
2021 Mar 100-105 practice question
Q61. - (Topic 5)
What are two recommended ways of protecting network device configuration files from outside network security threats? (Choose two.)
A. Allow unrestricted access to the console or VTY ports.
B. Use a firewall to restrict access from the outside to the network devices.
C. Always use Telnet to access the device command line because its data is automatically encrypted.
D. Use SSH or another encrypted and authenticated transport to access device configurations.
E. Prevent the loss of passwords by disabling password encryption.
Answer: B,D
Explanation:
Using a firewall is a must for networks of any size to protect the internal network from outside threats and unauthorized access. SSH traffic is encrypted while telnet is not, so it is always recommended to use SSH.
Q62. - (Topic 2)
How many simultaneous Telnet sessions does a Cisco router support by default?
A. 1
B. 2
C. 3
D. 4
E. 5
F. 6
Answer: E
Explanation:
By default, Cisco routers support virtual terminal interfaces 0-4 (5 total) which are used for telnet sessions.
Q63. - (Topic 1)
Refer to the exhibit.
Host A is sending a packet to Host B for the first time. What destination MAC address will Host A use in the ARP request?
A. 192.168.0.1
B. 172.16.0.50
C. 00-17-94-61-18-b0
D. 00-19-d3-2d-c3-b2
E. ff-ff-ff-ff-ff-ff
F. 255.255.255.255
Answer: E Explanation:
For the initial communication, Host A will send a broadcast ARP (all F's) to determine the correct address to use to reach the destination. ARP sends an Ethernet frame called an ARP request to every host on the shared link-layer legmen. The Ethernet header includes the source host MAC address and a destination address of all Fs representing a broadcast frame. The ARP request contains the sender's MAC and IP address and the target (destination) IP address. The target's MAC address is set to all 0s. ARP Request
Reference:
http://www.technicalhowto.com/protocols/arp/arp.html
Q64. - (Topic 1)
At which layer of the OSI model does the protocol that provides the information that is displayed by the show cdp neighbors command operate?
A. application
B. transport
C. network
D. physical
E. data link
Answer: E
Explanation:
CDP is a device discovery protocol that runs over Layer 2 (the data link layer) on all Cisco-manufactured devices (routers, bridges, access servers, and switches) and allows network management applications to discover Cisco devices that are neighbors of already known devices. With CDP, network management applications can learn the device type and the Simple Network Management Protocol (SNMP) agent address of neighboring devices running lower-layer, transparent protocols. CDP allows devices to share basic configuration information without even configuring any protocol specific information and is enabled by default on all interfaces. CDP is a Datalink Protocol occurring at Layer 2 of the OSI model. CDP is not routable and can only go over to directly connected devices. CDP is enabled, by default, on all Cisco devices. CDP updates are generated as multicasts every 60 seconds with a hold-down period of 180 seconds for a missing neighbor. The no cdp run command globally disables CDP, while the no cdp enable command disables CDP on an interface. Use show cdp neighbors to list out your directly connected Cisco neighboring devices. Adding the detail parameter will display the layer-3 addressing configured on the neighbor.
Reference: http://computernetworkingnotes.com/cisco-devices-administration-and-configuration/cisco-discoveryprotocol.html
Q65. - (Topic 1)
What are two common TCP applications? (Choose two.)
A. TFTP
B. SMTP
C. SNMP
D. FTP
E. DNS
Answer: B,D
Explanation:
SMTP uses TCP port 25, while FTP uses TCP ports 20 and 21.
Reference: http://pentestlab.wordpress.com/2012/03/05/common-tcpip-ports/
Renovate 100-105 brain dumps:
Q66. - (Topic 1)
Which three statements are true about the operation of a full-duplex Ethernet network? (Choose three.)
A. There are no collisions in full-duplex mode.
B. A dedicated switch port is required for each full-duplex node.
C. Ethernet hub ports are preconfigured for full-duplex mode.
D. In a full-duplex environment, the host network card must check for the availability of the network media before transmitting.
E. The host network card and the switch port must be capable of operating in full-duplex mode.
Answer: A,B,E
Explanation:
Half-duplex Ethernet is defined in the original 802.3 Ethernet and Cisco says you only use one wire pair with a digital signal running in both directions on the wire. It also uses the CSMA/CD protocol to help prevent collisions and to permit retransmitting if a collision does occur. If a hub is attached to a switch, it must operate in half-duplex mode because the end stations must be able to detect collisions. Half-duplex Ethernet—typically 10BaseT—is only about 30 to 40 percent efficient as Cisco sees it, because a large 10BaseT network will usually only give you 3- to 4Mbps—at most. Full-duplex Ethernet uses two pairs of wires, instead of one wire pair like half duplex. Also, full duplex uses a point-to-point connection between the transmitter of the transmitting device and the receiver of the receiving device, which means that with full-duplex data transfer, you get a faster data transfer compared to half duplex. And because the transmitted data is sent on a different set of wires than the received data, no collisions occur. The reason you don’t need to worry about collisions is because now Full-duplex Ethernet is like a freeway with multiple lanes instead of the single-lane road provided by half duplex. Full-duplex Ethernet is supposed to offer 100 percent efficiency in both directions; this means you can get 20Mbps with a 10Mbps Ethernet running full duplex, or 200Mbps for FastEthernet.
Q67. - (Topic 3)
Refer to the exhibit.
If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?
A. Router1>
B. Router1#
C. Router2>
D. Router2#
Answer: C
Explanation:
After resuming the telnet session by using the Enter key after it has been suspended, it will resume back to the telnet session so it will be back to the router2> prompt.
Q68. - (Topic 7)
Which value is indicated by the next hop in a routing table?
A. preference of the route source
B. IP address of the remote router for forwarding the packets
C. how the route was learned
D. exit interface IP address for forwarding the packets
Answer: D
Explanation:
The routing table contains network/next hop associations. These associations tell a router that a particular destination can be optimally reached by sending the packet to a specific router that represents the "next hop" on the way to the final destination. The next hop association can also be the outgoing or exit interface to the final destination.
Q69. - (Topic 4)
What happens when computers on a private network attempt to connect to the Internet through a Cisco router running PAT?
A. The router uses the same IP address but a different TCP source port number for each connection.
B. An IP address is assigned based on the priority of the computer requesting the connection.
C. The router selects an address from a pool of one-to-one address mappings held in the lookup table.
D. The router assigns a unique IP address from a pool of legally registered addresses for the duration of the connection.
Answer: A
Reference:
http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/nat_staticpat.html
Static PAT translations allow a specific UDP or TCP port on a global address to be translated to a specific port on a local address. That is, both the address and the port numbers are translated.
Static PAT is the same as static NAT, except that it enables you to specify the protocol (TCP or UDP) and port for the real and mapped addresses. Static PAT enables you to identify the same mapped address across many different static statements, provided that the port is different for each statement. You cannot use the same mapped address for multiple static NAT statements.
Port Address Translation makes the PC connect to the Internet but using different TCP source port.
Q70. - (Topic 3)
The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router. No routing protocols or other static routes are configured on the router. Which statement is true about this command?
A. The interface with IP address 192.168.10.2 is on this router.
B. The command sets a gateway of last resort for the router.
C. Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.
D. The command creates a static route for all IP traffic with the source address
192.168.100.160.
Answer: C
Explanation:
With 160 it's actually network address of /27 so any address within the range of .160-.191 network will be sent to 192.168.10.2