Exam Code: icnd 100 105 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass icnd 100 105 Exam.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 100-105 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 100-105 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/100-105-exam-dumps.html
Q11. - (Topic 3)
What is the purpose of assigning an IP address to a switch?
A. provides local hosts with a default gateway address
B. allows remote management of the switch
C. allows the switch to respond to ARP requests between two hosts
D. ensures that hosts on the same LAN can communicate with each other
Answer: B
Explanation:
A switch is a layer 2 device and doesn’t use network layer for packet forwarding. The IP
address may be used only for administrative purposes such as Telnet access or for network management purposes.
Q12. - (Topic 3)
Some routers have been configured with default routes. What are some of the advantages
of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Answer: B,D
Explanation:
Cisco administration 101: What you need to know about default routes Reference:
http://www.techrepublic.com/article/cisco-administration-101-what-you-need-to-know-about-default-routes/
Q13. - (Topic 1)
Refer to the exhibit.
A network has been planned as shown. Which three statements accurately describe the areas and devices in the network plan? (Choose three.)
A. Network Device A is a switch.
B. Network Device B is a switch.
C. Network Device A is a hub.
D. Network Device B is a hub.
E. Area 1 contains a Layer 2 device.
F. Area 2 contains a Layer 2 device.
Answer: A,D,E
Explanation:
Switches use a separate collision domain for each port, so device A must be a switch. Hubs, however, place all ports in the same collision domain so device B is a hub. Switches reside in layer 2 while hubs are layer 1 devices.
Q14. - (Topic 3)
Which two statements describe the IP address 10.16.3.65/23? (Choose two.)
A. The subnet address is 10.16.3.0 255.255.254.0.
B. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
C. The last valid host address in the subnet is 10.16.2.254 255.255.254.0
D. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
E. The network is not subnetted.
Answer: B,D
Explanation:
The mask 255.255.254.0 (/23) used with a Class A address means that there are 15 subnet bits and 9 host bits. The block size in the third octet is 2 (256 - 254). So this makes the subnets in 0, 2, 4, 6, etc., all the way to 254. The host 10.16.3.65 is in the 2.0 subnet. The next subnet is 4.0, so the broadcast address for the 2.0 subnet is 3.255. The valid host addresses are 2.1 through 3.254
Q15. - (Topic 2)
What does a host on an Ethernet network do when it is creating a frame and it does not have the destination address?
A. Drops the frame
B. Sends out a Layer 3 broadcast message
C. Sends a message to the router requesting the address
D. Sends out an ARP request with the destination IP address
Answer: D
Explanation:
In this case, it will send out an ARP request for MAC address of the destination IP (assuming it doesn't already have it in its table) and then address it to the destination's MAC address.
Q16. - (Topic 5)
Refer to the exhibit.
Serial 0/0 does not respond to a ping request from a host on the FastEthernet 0/0 LAN. How can this problem be corrected?
A. Enable the Serial 0/0 interface.
B. Correct the IP address for Serial 0/0.
C. Correct the IP address for FastEthernet 0/0
D. Change the encapsulation type on Serial 0/0
E. Enable autoconfiguration on the Serial 0/0 interface
Answer: A
Explanation:
Serial 0/0 interface is administratively down therefore, you will have to run the "no shutdown" command to enable the interface for data.
Q17. - (Topic 5)
Which of the following is true regarding the configuration of SwitchA?
A. only 5 simultaneous remote connections are possible
B. remote connections using ssh will require a username and password
C. only connections from the local network will be possible
D. console access to SwitchA requires a password
Answer: B
Q18. - (Topic 5)
What is the subnet broadcast address of the LAN connected to Router1?
A. 192.168.8.15
B. 192.168.8.31
C. 192.168.8.63
D. 192.168.8.127
Answer: A
Explanation:
The IP address assigned to FA0/1 is 192.168.8.9/29, making 192.168.8.15 the broadcast address.
Q19. - (Topic 7)
Which RFC was created to alleviate the depletion of IPv4 public addresses?
A. RFC 4193
B. RFC 1519
C. RFC 1518
D. RFC 1918
Answer: C
Q20. - (Topic 2)
Refer to the exhibit.
The ports that are shown are the only active ports on the switch. The MAC address table is shown in its entirety. The Ethernet frame that is shown arrives at the switch.
What two operations will the switch perform when it receives this frame? (Choose two.)
A. The MAC address of 0000.00aa.aaaa will be added to the MAC address table.
B. The MAC address of 0000.00dd.dddd will be added to the MAC address table.
C. The frame will be forwarded out of port fa0/3 only.
D. The frame will be forwarded out of fa0/1, fa0/2, and fa0/3.
E. The frame will be forwarded out of all the active ports.
Answer: A,D
Explanation:
If the switch already has the MAC address in its table for the destination, it will forward the frame directly to the destination port. If it was not already in its MAC table, then they frame would have been flooded out all ports except for the port that it came from. It will also add the MAC address of the source device to its MAC address table