Master the 156-915.80 Check Point Certified Security Expert Update - R80 content and be ready for exam day success quickly with this Pass4sure 156-915.80 exams. We guarantee it!We make it a reality and give you real 156-915.80 questions in our Check Point 156-915.80 braindumps.Latest 100% VALID Check Point 156-915.80 Exam Questions Dumps at below page. You can use our Check Point 156-915.80 braindumps and pass your exam.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Check Point 156-915.80 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 156-915.80 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/156-915.80-exam-dumps.html
P.S. Pinpoint 156-915.80 practice are available on Google Drive, GET MORE: https://drive.google.com/open?id=1kHtvfzv89_QPh4A3_cAnuAFq9mDuP3yP
New Check Point 156-915.80 Exam Dumps Collection (Question 7 - Question 16)
New Questions 7
You are responsible for the configuration of MegaCorpu2021s Check Point Firewall. You need to allow two NAT rules to match a connection. Is it possible? Give the BEST answer.
A. No, it is not possible to have more than one NAT rule matching a connection. When the firewall receives a packet belonging to a connection, it compares it against the first rule in the Rule Base, then the second rule, and so on. When it finds a rule that matches, it stops checking and applies that rule.
B. Yes, it is possible to have two NAT rules which match a connection, but only in using Manual NAT
(bidirectional NAT).
C. Yes, there are always as many active NAT rules as there are connections.
D. Yes, it is possible to have two NAT rules which match a connection, but only when using Automatic NAT (bidirectional NAT).
Answer: D
New Questions 8
To stop acceleration on a GAiA Security Gateway, enter command:
Answer:
fwaccel off
New Questions 9
As a Security Administrator, you must refresh the Client Authentication authorization time-out every time a new user connection is authorized. How do you do this? Enable the Refreshable Timeout setting:
A. in the user object's Authentication screen.
B. in the Gateway object's Authentication screen.
C. in the Limit tab of the Client Authentication Action Properties screen.
D. in the Global Properties Authentication screen.
Answer: C
New Questions 10
Type the full fw command and syntax that will show full synchronization status.
Answer:
fw ctl pstat
New Questions 11
Which of the following CLISH commands would you use to set the admin user's shell to bash?
A. set user admin shell bash
B. set user admin shell /bin/bash
C. set user admin shell = /bin/bash
D. set user admin /bin/bash
Answer: B
New Questions 12
Which statements about Management HA are correct?
1) Primary SmartCenter describes first installed SmartCenter
2) Active SmartCenter is always used to administrate with SmartConsole
3) Active SmartCenter describes first installed SmartCenter
4) Primary SmartCenter is always used to administrate with SmartConsole
A. 1 and 4
B. 2 and 3
C. 1 and 2
D. 3 and 4
Answer: C
New Questions 13
After filtering a fw monitor trace by port and IP, a packet is displayed three times; in the i, I, and o inspection points, but not in the O inspection point. Which is the likely source of the issue?
A. The packet has been sent out through a VPN tunnel unencrypted.
B. An IPSO ACL has blocked the packetu2021s outbound passage.
C. A SmartDefense module has blocked the packet.
D. It is due to NAT.
Answer: D
New Questions 14
Your R80 primary Security Management Server is installed on GAiA. You plan to schedule the Security Management Server to run fw logswitch automatically every 48 hours. How do you create this schedule?
A. On a GAiA Security Management Server, this can only be accomplished by configuring the command fw logswitch via the cron utility.
B. Create a time object, and add 48 hours as the interval. Open the primary Security Management Server objectu2021s Logs and Masters window, enable Schedule log switch, and select the Time object.
C. Create a time object, and add 48 hours as the interval. Open the Security Gateway object's Logs and Masters window, enable Schedule log switch, and select the Time object.
D. Create a time object, and add 48 hours as the interval. Select that time objectu2021s Global Properties > Logs and Masters window, to schedule a logswitch.
Answer: B
New Questions 15
Jennifer McHanry is CEO of ACME. She recently bought her own personal iPad. She wants use her iPad to access the internal Finance Web server. Because the iPad is not a member of the Active Directory domain, she cannot identify seamlessly with AD Query. However, she can enter her AD credentials in the Captive Portal and then get the same access as on her office computer. Her access to resources is based on rules in the R80 Firewall Rule Base.
To make this scenario work, the IT administrator must:
1) Enable Identity Awareness on a gateway and select Captive Portal as one of the Identity Sources.
2) In the Portal Settings window in the User Access section, make sure that Name and password login is selected.
3) Create a new rule in the Firewall Rule Base to let Jennifer McHanry access network destinations. Select accept as the Action.
Ms. McHanry tries to access the resource but is unable. What should she do?
A. Have the security administrator select the Action field of the Firewall Rule u201cRedirect HTTP connections to an authentication (captive) portalu201d
B. Have the security administrator reboot the firewall
C. Have the security administrator select Any for the Machines tab in the appropriate Access Role
D. Install the Identity Awareness agent on her iPad
Answer: A
New Questions 16
Fill in the blank with a numeric value. The default port number for standard TCP connections with the LDAP server is
Answer:
389
P.S. Easily pass 156-915.80 Exam with Certleader Pinpoint Dumps & pdf vce, Try Free: https://www.certleader.com/156-915.80-dumps.html ( New Questions)