The actual Cisco 200-120 answers and questions tend to be up to date by our technicians live. Youll get the latest simulated examination concerns that are in line with the existing Cisco examination. More notably, the particular up-date time prolonged to be able to A hundred and eighty times, displaying that you will have 50 percent any years time and energy to examine 200-120 puts.

2021 Dec ccna pass4sure 200-120 pdf:

Q41. - (Topic 5) 

Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.) 

A. Set the IP gateway to be used by the network. 

B. Perform host discovery used DHCPDISCOVER message. 

C. Configure IP address parameters from DHCP server to a host. 

D. Provide an easy management of layer 3 devices. 

E. Monitor IP performance using the DHCP server. 

F. Assign and renew IP address from the default pool. 

Answer: C,F 


Q42. - (Topic 2) 

Refer to the exhibit. 

A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2? 

A. interface FastEthernet 0/1 channel-group 1 mode active switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode active switchport trunk encapsulation dot1q switchport mode trunk 

B. interface FastEthernet 0/1 channel-group 2 mode auto switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 2 mode auto switchport trunk encapsulation dot1q switchport mode trunk 

C. interface FastEthernet 0/1 channel-group 1 mode desirable switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode desirable switchport trunk encapsulation dot1q switchport mode trunk 

D. interface FastEthernet 0/1 channel-group 1 mode passive switchport trunk encapsulation dot1q switchport mode trunk interface FastEthernet 0/2 channel-group 1 mode passive switchport trunk encapsulation dot1q switchport mode trunk 

Answer:


Q43. - (Topic 3) 

How is an EUI-64 format interface ID created from a 48-bit MAC address? 

A. by appending 0xFF to the MAC address 

B. by prefixing the MAC address with 0xFFEE 

C. by prefixing the MAC address with 0xFF and appending 0xFF to it 

D. by inserting 0xFFFE between the upper three bytes and the lower three bytes of the MAC address 

E. by prefixing the MAC address with 0xF and inserting 0xF after each of its first three bytes 

Answer:


Q44. - (Topic 3) 

Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.) 

A. Global addresses start with 2000::/3. 

B. Link-local addresses start with FE00:/12. 

C. Link-local addresses start with FF00::/10. 

D. There is only one loopback address and it is ::1. 

E. If a global address is assigned to an interface, then that is the only allowable address for the interface. 

Answer: A,D 


Q45. - (Topic 3) 

What are three features of the IPv6 protocol? 

(Choose three.) 

A. optional IPsec 

B. autoconfiguration 

C. no broadcasts 

D. complicated header 

E. plug-and-play 

F. checksums 

Answer: B,C,E 


Rebirth ccna 640-802 vs 200-120:

Q46. - (Topic 7) 

Scenario: 

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links. 

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices. 

An OSPF neighbor adjacency is not formed between R3 in the main office and R4 in the Branchl office. What is causing the problem? 

A. There is an area ID mismatch. 

B. There is a Layer 2 issue; an encapsulation mismatch on serial links. 

C. There is an OSPF hello and dead interval mismatch. 

D. The R3 router ID is configured on R4. 

Answer:


Q47. - (Topic 9) 

Refer to the exhibit. 

What is the effect of the given configuration? 

A. It configures an inactive switch virtual interface. 

B. It configures an active management interface. 

C. It configures the native VLAN. 

D. It configures the default VLAN. 

Answer:


Q48. - (Topic 4) 

Which command shows your active Telnet connections? 

A. show cdp neigbors 

B. show session 

C. show users 

D. show vty logins 

Answer:


Q49. - (Topic 9) 

Which three statements about link-state routing are true? (Choose three.) 

A. Routes are updated when a change in topology occurs. 

B. Updates are sent to a multicast address by default. 

C. OSPF is a link-state protocol. 

D. Updates are sent to a broadcast address. 

E. RIP is a link-state protocol. 

F. It uses split horizon. 

Answer: A,B,C 


Q50. - (Topic 5) 

Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.) 

A. SNMPv3 enhanced SNMPv2 security features. 

B. SNMPv3 added the Inform protocol message to SNMP. 

C. SNMPv2 added the Inform protocol message to SNMP. 

D. SNMPv3 added the GetBulk protocol messages to SNMP. 

E. SNMPv2 added the GetBulk protocol message to SNMP. 

F. SNMPv2 added the GetNext protocol message to SNMP. 

Answer: A,C,E