It is more faster and easier to pass the Cisco 200-120 exam by using Practical Cisco CCNA Cisco Certified Network Associate CCNA (803) questuins and answers. Immediate access to the Up to the minute 200-120 Exam and find the same core area 200-120 questions with professionally verified answers, then PASS your exam with a high score now.

2021 Feb dumps 200-120:

Q151. DRAG DROP - (Topic 4) 

Answer: 


Q152. - (Topic 8) 

Which two statistics appear in show frame-relay map output? (Choose two.) 

A. the number of BECN packets that are received by the router 

B. the value of the local DLCI 

C. the number of FECN packets that are received by the router 

D. the status of the PVC that is configured on the router 

E. the IP address of the local router 

Answer: B,D 


Q153. - (Topic 2) 

Refer to the exhibit. 

Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached? 

A. VLANs have not been created yet. 

B. An IP address must be configured for the port. 

C. The port is currently configured for access mode. 

D. The correct encapsulation type has not been configured. 

E. The “no shutdown” command has not been entered for the port. 

Answer:


Q154. - (Topic 8) 

What is the purpose of Inverse ARP? 

A. to map a known IP address to a MAC address 

B. to map a known DLCI to a MAC address 

C. to map a known MAC address to an IP address 

D. to map a known DLCI to an IP address 

E. to map a known IP address to a SPID 

F. to map a known SPID to a MAC address 

Answer:


Q155. - (Topic 7) 

A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. 

The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem? 

A. The OSPF area is not configured properly. 

B. The priority on R1 should be set higher. 

C. The cost on R1 should be set higher. 

D. The hello and dead timers are not configured properly. 

E. A backup designated router needs to be added to the network. 

F. The OSPF process ID numbers must match. 

Answer:


Up to the immediate present ccna 200-120:

Q156. - (Topic 4) 

What is the default administrative distance of OSPF? 

A. 90 

B. 100 

C. 110 

D. 120 

Answer:


Q157. - (Topic 4) 

Which command encrypts all plaintext passwords? 

A. Router# service password-encryption 

B. Router(config)# password-encryption 

C. Router(config)# service password-encryption 

D. Router# password-encryption 

Answer:


Q158. - (Topic 4) 

Why do large OSPF networks use a hierarchical design? (Choose three.) 

A. to decrease latency by increasing bandwidth 

B. to reduce routing overhead 

C. to speed up convergence 

D. to confine network instability to single areas of the network 

E. to reduce the complexity of router configuration 

F. to lower costs by replacing routers with distribution layer switches 

Answer: B,C,D 


Q159. - (Topic 8) 

What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.) 

A. They create split-horizon issues. 

B. They require a unique subnet within a routing domain. 

C. They emulate leased lines. 

D. They are ideal for full-mesh topologies. 

E. They require the use of NBMA options when using OSPF. 

Answer: B,C 


Q160. - (Topic 2) 

Refer to Exhibit: How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches? 

A. one 

B. two 

C. six 

D. twelve 

Answer: