Exam Code: 200-401 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Managing Industrial Networks with Cisco Networking Technologies
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 200-401 Exam.

2021 Nov vitobloc 200 em-401/549 preis:

Q1. - (Topic 1) 

A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured? 

A. 255.255.240.0 

B. 255.255.255.128 

C. 255.255.255.192 

D. 255.255.255.224 

E. 255.255.255.240 

F. 255.255.255.248 

Answer:


Q2. - (Topic 2) 

Exhibit: 

Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation? 

A. a router with two Ethernet interfaces 

B. a switch with two Ethernet interfaces 

C. a router with one Ethernet and one serial interface 

D. a switch with one Ethernet and one serial interface 

E. a router with one Ethernet and one modem interface 

Answer:


Q3. - (Topic 2) 

What are the two most relevant factors in determining the class of administration that is required to maintain the telecommunications infrastructure? (Choose two.) 

A. the size of the infrastructure 

B. the complexity of the infrastructure 

C. the age of the infrastructure 

D. the industry that the infrastructure supports 

E. the physical environment of the infrastructure 

Answer: A,B 


Q4. - (Topic 2) 

According to the Purdue Reference Model, at which layer would you perform manufacturing operations and control? 

A. Level 0 

B. Level 1 

C. Level 2 

D. Level 3 

E. Level 4 

Answer:


Q5. - (Topic 2) 

What is the purpose of Spanning Tree Protocol? 

A. to prevent routing loops 

B. to create a default route 

C. to provide multiple gateways for hosts 

D. to maintain a loop-free Layer 2 network topology 

E. to enhance the functions of SNMP 

Answer:


Most recent synergy 200-401:

Q6. - (Topic 5) 

What is a reason to use privileged EXEC mode on an industrial switch? 

A. to verify commands that you have entered 

B. to change terminal settings 

C. to configure VLAN parameters 

D. to configure parameters that apply to the entire switch 

Answer:


Q7. - (Topic 5) 

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used? 

A. hop count 

B. administrative distance 

C. link bandwidth 

D. link delay 

E. link cost 

Answer:


Q8. - (Topic 2) 

Exhibit: 

Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration? 

A. These commands need to be added to the configuration:C-router(config)# router eigrp 123C-router(config-router)# network 172.19.0.0 

B. These commands need to be added to the configuration:C-router(config)# router ospf 1C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0 

C. These commands need to be added to the configuration:C-router(config)# router ripC-router(config-router)# network 172.19.0.0 

D. No further routing configuration is required. 

Answer:


Q9. - (Topic 2) 

Exhibit: 

Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch? 

A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network. 

B. allows connectivity between Host A and other devices in the network. 

C. allows connectivity between Host B and other devices in the network. 

D. allows the switch to pass traffic between Host A and Host B 

Answer:


Q10. - (Topic 5) 

Which two commands can help you to determine what image is running on your industrial switch? (Choose two.) 

A. show version 

B. show spanning-tree 

C. show interface-switch 

D. show interfaces gigabitEthernet x/y switchport 

E. show license 

Answer: A,E