It is impossible to pass Cisco 200-601 exam without any help in the short term. Come to Testking soon and find the most advanced, correct and guaranteed Cisco 200-601 practice questions. You will get a surprising result by our Improved Managing Industrial Networking for Manufacturing with Cisco Technologies practice guides.

2021 Oct 200-601 torrent

Q1. If.the Link Fault alarm is connected to the minor relay and the FCS Bit Error Rate alarm is connected to the major relay, which commands will create an alarm profile called GigE with the alarms correctly mapped to the minor and major relays? 

A. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 4 Switch(config-alarm-prof)#relay minor 1 

B. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 3 Switch(config-alarm-prof)#relay minor 1 

C. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 3 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 3 

D. Switch(config)#alarm profile GigE Switch(config-alarm-prof)#alarm 1 4 Switch(config-alarm-prof)#relay major 1 Switch(config-alarm-prof)#relay minor 4 

Answer: A 


Q2. What percentage of an I/O connection would you set the RPI in order to ensure the application has the most current data? 

A. RPI at 50% of IO rate 

B. RPI at 25% of IO rate 

C. PI to 25% of PAC scan rate 

D. Set RPI to 50% of PAC scan rate 

Answer: A 


Q3. A ProfiNET management system operator is unable to see diagnostic information for a Cisco Industrial Ethernet switch that has been added to a SIMATIC management station. Based on the provided CLI output, which statement is correct? 

switch# show profinet status 

State.: Enabled 

Vlan.: 201 

Id.: IE2000-Switch 

Connected : Yes 

ReductRatio : 128 

GSD version : Mis-match 

A. The assigned ProfiNET VLAN is not valid and should be less than 100 

B. LLDP has been disabled on this switch 

C. The GSD file version on the switch does not match the GSD file version on the management station 

D. The Reduction Ration has been set too low 

Answer: C 


Q4. Refer to the exhibit. 

Network Faceplates have not been installed on the HMI and so you need to map a network based on information available from RSLinx. Which most accurately represents the network configuration? 

A. 

B. 

C. 

D. 

Answer: B 


Q5. You are making changes to a Stratix 5700 using an Add On Profile (AOP) and a controller which is on-line with RSLogix5000. When do the changes you have made get published to the switch? 

A. While online in RSLogix 5000 software the changes made in the AOP are pushed to the switch after pressing the Set button. 

B. All of the changes are automatically pushed to the switch. 

C. Changes to the AOP can only be made from the switch, not in RSLogix 5000. 

D. RSLogix 5000 will push the changes in the AOP to the Stratix 5700 when you right click on the switch, and choose download to switch 

Answer: A 


Most up-to-date 200-601 free practice questions:

Q6. Refer to the exhibit. 

Which two parameters can be used to diagnose an overloaded system? (Choose two) 

A. Ethernet Port 1 Speed 

B. Module Resource Allocation Actual Rate 

C. Class 3 Received bytes per second 

D. Media Counters Alignment Errors 

E. TCP Connections Active 

Answer: B,E 


Q7. Which selection is a reason why IGMP snooping should be configured on a switched network? 

A. IGMP snooping populates the snooping table with the results of DHCP requests and can be used by Dynamic ARP Inspection to block IP spoofing attacks at Layer-2. 

B. IGMP snooping verifies the source IP address of every IPv4 packet to ensure that it hasn't been originated from a port different than its return path. 

C. IGMP snooping is used to filter ping requests and results to avoid overflowing the MAC address table of the switch. 

D. IGMP snooping allows a Layer-2 switch to limit the transmission of multicast frames to only the ports that have members of the relevant IGMP group. 

Answer: D 


Q8. It is determined that an intermittent high packet loss event is occurring within a segment of the network. The assigned task is to determine the cause. Which of these conditions should be suspected? 

A. 

B. 

C. 

D. 

Answer: D 


Q9. AP CAPWAP control traffic should be isolated from wireless client traffic. Which scenario represents the correct configuration to support the SSIDs of this controller-based access point in FlexConnect local switching mode? 

A. 

B. 

C. 

D. 

Answer: C 


Q10. A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface 

FastEthernet1/3. Based on the provided CLI output, which statement is correct? 

switch#show profinet lldp Fa1/1.port-003-00000 On Fa1/2.port-004-00000 On Fa1/3.port-005-00000 Off Fa1/4.port-006-00000 Off Fa1/5.port-007-00000 On Fa1/6.port-008-00000 Off Fa1/7.port-009-00000 On Fa1/8.port-010-00000 Off 

A. LLDP has been disabled on this switch 

B. The connected device is not sending LLDP packets with ProfiNET extensions 

C. The port label needs to be changed on interface FastEthernet 1/3 to "port-003-00000" 

D. ProfiNET is disabled on this switch 

Answer: B