Our Cisco Cisco exam dumps are generally designed and produced by simply Pass4sure IT professionals which often revise the logical and beneficial 300-115 simulated test. Pass4sure s Cisco 300-115 check products may not only allow you to get certified however also save your current time and money. The experts update our Cisco Cisco exam training materials on regular basis. You can attempt our totally free 300-115 test demos before buying with Pass4sure.com.

2021 Nov cbt nuggets ccnp switch 300-115 download:

Q21. Which configuration command ties the router hot standby priority to the availability of its interfaces?

A. standby group

B. standby priority

C. backup interface

D. standby track

Answer: D


Q22. Refer to the exhibit.

A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)

A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination

B. A remote SPAN VLAN on the distribution and access layer switch

C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination

D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination

E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination

F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination

Answer: BCD


Q23. Which option describes a limitation of LLDP?

A. LLDP cannot provide information about VTP.

B. LLDP does not support TLVs.

C. LLDP can discover only Windows servers.

D. LLDP can discover up to two devices per port.

Answer: A


Q24. After implementing VTP, the extended VLANs are not being propagated to other VTP switches. What should be configured for extended VLANs?

A. VTP does not support extended VLANs and should be manually added to all switches.

B. Enable VTP version 3, which supports extended VLAN propagation.

C. VTP authentication is required when using extended VLANs because of their ability to cause network instability.

D. Ensure that all switches run the same Cisco IOS version. Extended VLANs will not propagate to different IOS versions when extended VLANs are in use.

Answer: B


Q25. An access switch has been configured with an EtherChannel port. After configuring SPAN to monitor this port, the network administrator notices that not all traffic is being replicated to the management server. What is a cause for this issue?

A. VLAN filters are required to ensure traffic mirrors effectively.

B. SPAN encapsulation replication must be enabled to capture EtherChannel destination traffic.

C. The port channel can be used as a SPAN source, but not a destination.

D. RSPAN must be used to capture EtherChannel bidirectional traffic.

Answer: C


Down to date switch 300-115 pdf:

Q26. Which VRRP router is responsible for forwarding packets that are sent to the IP addresses of the virtual router?

A. virtual router master

B. virtual router backup

C. virtual router active

D. virtual router standby

Answer: A


Q27. The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?

A. The command effectively removed all other working VLANs and replaced them with the new VLANs.

B. VTP pruning removed all unused VLANs.

C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.

D. Allowing additional VLANs across the trunk introduced a loop in the network.

Answer: A


Q28. Which command correctly configures standby tracking for group 1 using the default decrement priority value?

A. standby 1 track 100

B. standby 1 track 100 decrement 1

C. standby 1 track 100 decrement 5

D. standby 1 track 100 decrement 20

Answer: A


Q29. When you design a switched network using VTPv2, how many VLANs can be used to carry user traffic?

A. 1000

B. 1001

C. 1024

D. 2048

E. 4095

F. 4096

Answer: B


Q30. Refer to the exhibit.

How many bytes are added to each frame as a result of the configuration?

A. 4-bytes except the native VLAN

B. 8-bytes except the native VLAN

C. 4-bytes including native VLAN

D. 8-bytes including native VLAN

Answer: A