There is a good interactive space on Examcollection. You can chat with other examinees. Learn coming from each other and make progress together. The actual candidates who have handed the Cisco 300-206 exam will certainly pass on their wisdom to you. Create full utilization of their Cisco examination notes. Theyre an invaluable asset on your Cisco Cisco exam preparation. You will find essentially the most advanced, correct and guaranteed Cisco 300-206 exam questions and answers. You will end up being ready for that Cisco 300-206 exam questions on the examination day. Find out more 300-206 information and lay a solid foundation for advancements within Cisco Cisco 300-206 career.

2021 Dec examcollection 300-206:

Q61. CORRECT TEXT 

You are a network security engineer for the Secure-X network. You have been tasked with 

implementing dynamic network object NAT with PAT on a Cisco ASA. You must configure the Cisco ASA such that the source IP addresses of all internal hosts are translated to a single IP address (using different ports) when the internal hosts access the Internet. 

To successfully complete this activity, you must perform the following tasks: 

. Use the Cisco ASDM GUI on the Admin PC to configure dynamic network object NAT with PAT using the following parameters: 

. Network object name: Internal-Networks 

. IP subnet: 10.10.0.0/16 

. Translated IP address: 192.0.2.100 

. Source interface: inside 

. Destination interface: outside 

NOTE: The object (TRANSLATED-INSIDE-HOSTS) for this translated IP address has already been created for your use in this activity. 

NOTE: Not all ASDM screens are active for this exercise. 

NOTE: Login credentials are not needed for this simulation. 

. In the Cisco ASDM, display and view the auto-generated NAT rule. 

. From the Employee PC, generate traffic to SP-SRV by opening a browser and navigating to http://sp-srv.sp.public. 

. From the Guest PC, generate traffic to SP-SRV by opening a browser and navigating to http://sp-srv.sp.public. 

. At the CLI of the Cisco ASA, display your NAT configuration. You should see the configured policy and statistics for translated packets. 

. At the CLI of the Cisco ASA, display the translation table. You should see dynamic translations for the Employee PC and the Guest PC. Both inside IP addresses translate to the same IP address, but using different ports. 

You have completed this exercise when you have configured and successfully tested dynamic network object NAT with PAT. 

Answer: See the explanation for detailed answer to this sim question. 


Q62. When a Cisco ASA is configured in multicontext mode, which command is used to change between contexts? 

A. changeto config context 

B. changeto context 

C. changeto/config context change 

D. changeto/config context 2 

Answer: B 


Q63. An SNMP host is an IP address to which SNMP notifications and traps are sent. To configure SNMFV3 hosts, which option must you configure in addition to the target IP address? 

A. the Cisco ASA as a DHCP server, so the SNMFV3 host can obtain an IP address 

B. a username, because traps are only sent to a configured user 

C. SSH, so the user can connect to the Cisco ASA 

D. the Cisco ASA with a dedicated interface only for SNMP, to process the SNMP host traffic. 

Answer: B 

Explanation: The username can be seen here on the ASDM simulator screen shot: 


Q64. Which statement about traffic storm control behavior is true? 

A. Traffic storm control cannot determine if the packet is unicast or broadcast. 

B. If you enable broadcast and multicast traffic storm control and the combined broadcast and multicast traffic exceeds the level within a 1 second traffic storm interval, storm control drops all broadcast and multicast traffic until the end of the storm interval 

C. Traffic storm control uses the Individual/Group bit in the packet source address to determine if the packet is unicast or broadcast. 

D. Traffic storm control monitors incoming traffic levels over a 10 second traffic storm control interval 

Answer: B 


Q65. Which three options are default settings for NTP parameters on a Cisco device? (Choose three.) 

A. NTP authentication is enabled. 

B. NTP authentication is disabled. 

C. NTP logging is enabled. 

D. NTP logging is disabled. 

E. NTP access is enabled. 

F. NTP access is disabled. 

Answer: B,D,E 


Refresh 300-206 labs:

Q66. Which Cisco product provides a GUI-based device management tool to configure Cisco access routers? 

A. Cisco ASDM 

B. Cisco CP Express 

C. Cisco ASA 5500 

D. Cisco CP 

Answer: D 


Q67. Which configuration keyword will configure SNMPv3 with authentication but no encryption? 

A. Auth 

B. Priv 

C. No auth 

D. Auth priv 

Answer: A 


Q68. Which cloud characteristic is used to describes the sharing of physical resource between various 

entities ? 

A. Elasticity 

B. Ubiquitous access 

C. Multitenancy 

D. Resiliency 

Answer: D 

Explanation: 

http://www.cisco.com/web/about/ac123/ac147/archived_issues/ipj_12-3/123_cloud1.html 


Q69. Which two statements about zone-based firewalls are true? (Choose two.) 

A. More than one interface can be assigned to the same zone. 

B. Only one interface can be in a given zone. 

C. An interface can only be in one zone. 

D. An interface can be a member of multiple zones. 

E. Every device interface must be a member of a zone. 

Answer: A,C 


Q70. Which function in the Cisco ADSM ACL Manager pane allows an administrator to search for a specfic element? 

A. Find 

B. Device Management 

C. Search 

D. Device Setup 

Answer: A