Testking provides all the Cisco certification exam preparation materials. If you have handed the Cisco 200-125 exam soon after using our products, you are able to choose to have other certification exam dumps following time in a discounted price. Acquire your own Cisco 200-125 exam goods today and pass the exam tomorrow! 99% passing rate and 100% money rear if fail. Using Testkings Cisco 200-125 training course is a one-stop remedy to the Cisco certification. Join our training team and have certified soon using the Cisco Cisco exam questions and answers. Theres never a cheaper means like this to get through your Cisco 200-125 exam. Frequent updated Cisco Cisco practice exams are also available at Testking.com. No far more charges, ever.
2021 Mar 200-125 actual exam
Q21. - (Topic 3)
Refer to the exhibit.
When running EIGRP, what is required for RouterA to exchange routing updates with RouterC?
A. AS numbers must be changed to match on all the routers
B. Loopback interfaces must be configured so a DR is elected
C. The no auto-summary command is needed on Router A and Router C
D. Router B needs to have two network statements, one for each connected network
Answer: A
Explanation:
This question is to examine the understanding of the interaction between EIGRP routers. The following information must be matched so as to create neighborhood.
EIGRP routers to establish, must match the following information:
1. AS Number;
2. K value.
Q22. . - (Topic 3)
A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?
A. It checks the configuration register.
B. It attempts to boot from a TFTP server.
C. It loads the first image file in flash memory.
D. It inspects the configuration file in NVRAM for boot instructions.
Answer: A
Explanation:
Default (normal) Boot Sequence
Power on Router - Router does POST - Bootstrap starts IOS load - Check configuration register to see what mode the router should boot up in (usually 0x2102 to read startup- config in NVRAM / or 0x2142 to start in "setup-mode") - check the startup-config file in NVRAM for boot-system commands - load IOS from Flash.
Q23. - (Topic 5)
Which statement describes VRRP object tracking?
A. It monitors traffic flow and link utilization.
B. It ensures the best VRRP router is the virtual router master for the group.
C. It causes traffic to dynamically move to higher bandwidth links.
D. It thwarts man-in-the-middle attacks.
Answer: B
Explanation:
Object tracking is the process of tracking the state of a configured object and uses that state to determine the priority of the VRRP router in a VRRP group.
Q24. - (Topic 3)
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0? (Choose two.)
A. Router(config)# router ospf 0
B. Router(config)# router ospf 1
C. Router(config)# router ospf area 0
D. Router(config-router)# network 192.168.16.0 0.0.0.255 0
E. Router(config-router)# network 192.168.16.0 0.0.0.255 area 0
F. Router(config-router)# network 192.168.16.0 255.255.255.0 area 0
Answer: B,E
Explanation:
In the router ospf command, the ranges from 1 to 65535 so o is an invalid number -> but To configure OSPF, we need a wildcard in the “network” statement, not a subnet mask. We also need to assgin an area to this process ->.
Q25. - (Topic 5)
How is an EUI-64 format interface ID created from a 48-bit MAC address?
A. by appending 0xFF to the MAC address
B. by prefixing the MAC address with 0xFFEE
C. by prefixing the MAC address with 0xFF and appending 0xFF to it
D. by inserting 0xFFFE between the upper three bytes and the lower three bytes of the MAC address
E. by prefixing the MAC address with 0xF and inserting 0xF after each of its first three bytes
Answer: D
Explanation:
The modified EUI-64 format interface identifier is derived from the 48-bit link-layer (MAC) address by inserting the hexadecimal number FFFE between the upper three bytes (OUI field) and the lower three bytes (serial number) of the link layer address.
Refresh 200-125 braindumps:
Q26. - (Topic 8)
Which feature can you implement to reserve bandwidth for VoIP calls across the call path?
A. PQ
B. CBWFQ
C. round robin
D. RSVP
Answer: D
Q27. - (Topic 7)
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Answer: C
Explanation:
The “show ip ospf interface command on R3 and R5 shows that the hello and dead intervals do not match. They are 50 and 200 on R3 and 10 and 40 on R5.
Q28. - (Topic 8)
What are three broadband wireless technologies? (Choose three.)
A. WiMax
B. satellite Internet
C. municipal Wi-Fi
D. site-to-site VPN
E. DSLAM
F. CMTS
Answer: A,B,C
Q29. - (Topic 6)
A network administrator needs to configure port security on a switch. Which two statements are true? (Choose two.)
A. The network administrator can apply port security to dynamic access ports.
B. The network administrator can apply port security to EtherChannels.
C. When dynamic MAC address learning is enabled on an interface, the switch can learn new addresses, up to the maximum defined.
D. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
E. The network administrator can configure static secure or sticky secure MAC addresses in the voice VLAN.
Answer: C,D
Explanation:
Follow these guidelines when configuring port security:
+ Port security can only be configured on static access ports, trunk ports, or 802.1Q tunnel ports.
+ A secure port cannot be a dynamic access port.
+ A secure port cannot be a destination port for Switched Port Analyzer (SPAN).
+ A secure port cannot belong to a Fast EtherChannel or Gigabit EtherChannel port group.
+ You cannot configure static secure or sticky secure MAC addresses on a voice VLAN.
+ When you enable port security on an interface that is also configured with a voice VLAN, you must set the maximum allowed secure addresses on the port to at least two.
+ If any type of port security is enabled on the access VLAN, dynamic port security is automatically enabled on the voice VLAN.
+ When a voice VLAN is configured on a secure port that is also configured as a sticky secure port, all addresses seen on the voice VLAN are learned as dynamic secure addresses, and all addresses seen on the access VLAN (to which the port belongs) are learned as sticky secure addresses.
+ The switch does not support port security aging of sticky secure MAC addresses.
+ The protect and restrict options cannot be simultaneously enabled on an interface.
(Reference: http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_19_ea1
/configuration/guide/swtrafc.html)
Q30. - (Topic 6)
Refer to the exhibit.
Statements A, B, C, and D of ACL 10 have been entered in the shown order and applied to interface E0 inbound, to prevent all hosts (except those whose addresses are the first and last IP of subnet 172.21.1.128/28) from accessing the network. But as is, the ACL does not restrict anyone from the network. How can the ACL statements be re-arranged so that the system works as intended?
A. ACDB
B. BADC
C. DBAC
D. CDBA
Answer: D
Explanation:
Routers go line by line through an access list until a match is found and then will not look any further, even if a more specific of better match is found later on in the access list. So, it it best to begin with the most specific entries first, in this cast the two hosts in line C and D. Then, include the subnet (B) and then finally the rest of the traffic (A).