It is more faster and easier to pass the Cisco 200 125 ccna exam by using 100% Correct Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) questuins and answers. Immediate access to the Latest ccna 200 125 pdf Exam and find the same core area ccna 200 120 vs 200 125 questions with professionally verified answers, then PASS your exam with a high score now.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/200-125-exam-dumps.html

P.S. 100% Correct 200-125 discount pack are available on Google Drive, GET MORE: https://drive.google.com/open?id=1kYtwvDfK3CIMnjUzKdkde8F69Zg0NhM8


New Cisco 200-125 Exam Dumps Collection (Question 9 - Question 18)

Q1. Which NAT type is used to translate a single inside address to a single outside address?

A. dynamic NAT

B. NAT overload

C. PAT

D. static NAT

Answer: D

Explanation:

Network address translation (NAT) is the process ofmodifying IP addressinformation in IP packet headers while in transit across a traffic routing device.

There are two different types of NAT:

u2711 NAT

u2711 PAT


Q2. On which type of device is every port in the same collision domain?

A. a router

B. a Layer 2 switch

C. a hub

Answer: C

Explanation:

Collision domain

A collision domain is, as the name implies, a part of a network where packet collisions can occur. A collision occurs when two devices send a packet at the same time on the shared network segment. The packets collide and both devices must send the packets again, which reduces network efficiency. Collisions are often in a hub environment, because each port on a hub is in the same collision domain. By contrast, each port on a bridge, a switch or a router is in a separate collision domain.


Q3. Which feature can you use to monitor traffic on a switch by replicating it to another port or ports on the same switch?

A. copy run start

B. traceroute

C. the ICMP Echo IP SLA

D. SPAN

Answer: D

Explanation: A source port, also called a monitored port, is a switched or routed port that you monitor for network traffic analysis. In a single local SPAN session or RSPAN source session, you can monitor source port traffic, such as received (Rx), transmitted (Tx), or bidirectional (both). The switch supports any number of source ports (up to the maximum number of available ports on the switch) and any number of source VLANs.

A source port has these characteristics:

u2711 It can be any port type, such as EtherChannel, Fast Ethernet, Gigabit Ethernet, and so forth.

u2711 It can be monitored in multiple SPAN sessions.

u2711 It cannot be a destination port.

u2711 Each source port can be configured with a direction (ingress, egress, or both) to monitor. For EtherChannel sources, the monitored direction applies to all physical

ports in the group.

u2711 Source ports can be in the same or different VLANs.

u2711 For VLAN SPAN sources, all active ports in the source VLAN are included as source ports.


Q4. Which option describes the purpose of traffic policing?

A. It prioritizes routing protocol traffic.

B. It remarks traffic that is below the CIR

C. It drops traffic that exceeds the CIR.

D. It queues and then transmits traffic that exceeds the CIR.

Answer: C

Explanation:

Traffic policing allows you to control the maximum rate of traffic transmitted or received on an interface. Traffic policing is often configured on interfaces at the edge of a network to limit traffic into or out of the network. In most Traffic Policing configurations, traffic that falls within the rate parameters is transmitted, whereas traffic that exceeds the parameters is dropped or transmitted with a different priority.


Q5. What are two reasons that duplex mismatches can be difficult to diagnose? (Choose two.)

A. The interface displays a connected (up/up) state even when the duplex settings are mismatched.

B. The symptoms of a duplex mismatch may be intermittent.

C. Autonegotiation is disabled.

D. Full-duplex interfaces use CSMA/CD logic, so mismatches may be disguised by collisions.

E. 1-Gbps interfaces are full-duplex by default.

Answer: A,B


Q6. Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Choose two)

A. no logging console

B. logging host ip-address

C. terminal monitor

D. show logging | redirect flashioutput.txt

E. snmp-server enable traps syslog

Answer: B,C


Q7. Refer to the exhibit.

Which statement describes the effect of this configuration?

A. The VLAN 10 VTP configuration is displayed.

B. VLAN 10 spanning-tree output is displayed.

C. The VLAN 10 configuration is saved when the router exits VLAN configuration mode.

D. VLAN 10 is added to the VLAN database.

Answer: D


Q8. What is the effect of using the service password-encryption command?

A. Only the enable password will be encrypted.

B. It will encrypt all current and future passwords.

C. It will encrypt the secret password and remove the enable secret password from the configuration.

D. Only the enable secret password will be encrypted.

E. Only passwords configured after the command has been entered will be encrypted.

Answer: B

Explanation:

Enable vty, console, AUX passwords are configured on the Cisco device. Use the show run command to show most passwords in clear text. If the service password-encryption is used, all the passwords are encrypted. As a result, the security of device access is improved.


Q9. Which three commands must you enter to create a trunk that allows VLAN 20? (Choose three)

A. Switch(config-if)#switchport mode dynamic auto

B. Switch(config-if)#switchport mode trunk

C. Switch(config-if)#switchport trunk allowed vlan 20

D. Switch(config-if)#switchport mode dynamic desirable

E. Switch(config-if)#switchport trunk encapsulation dotlq

F. Switch(config-if)#switchport trunk native vlan 20

Answer: B,E,F


Q10. Which two statements about IPv6 router advertisement messages are true? (Choose two.)

A. They use ICMPv6 type 134.

B. The advertised prefix length must be 64 bits.

C. The advertised prefix length must be 48 bits.

D. They are sourced from the configured IPv6 interface address.

E. Their destination is always the link-local address of the neighboring node.

Answer: A,B


100% Latest Cisco 200-125 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com//dumps/200-125/ (New 890 Q&As)