It is impossible to pass Cisco ccna routing and switching 200 125 pdf exam without any help in the short term. Come to Passleader soon and find the most advanced, correct and guaranteed Cisco ccna 200 125 pdf practice questions. You will get a surprising result by our Most recent CCNA Cisco Certified Network Associate CCNA (v3.0) practice guides.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 200-125 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 200-125 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/200-125-exam-dumps.html

P.S. 100% Correct 200-125 pdf are available on Google Drive, GET MORE: https://www.slideshare.net/reinigerodp/certleader-200-125examquestionsmaterials


New Cisco 200-125 Exam Dumps Collection (Question 1 - Question 10)

Q1. Refer to the exhibit.

The technician wants to upload a new IOS in the router while keeping the existing IOS. What is the maximum size of an IOS file that could be loaded if the original IOS is also kept in flash?

A. 3 MB

B. 4 MB

C. 5 MB

D. 7 MB

E. 8 MB

Answer: B

Explanation:

In this example, there are a total of 8 MB, but 3.8 are being used already, so another file as large as 4MB can be loaded in addition to the original file.


Q2. Refer to the exhibit.

A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2. What causes this behavior?

A. trunk mode mismatches

B. allowing only VLAN 2 on the destination

C. native VLAN mismatches

D. VLANs that do not correspond to a unique IP subnet

Answer: C

Explanation:

Untagged frames are encapsulated with the native VLAN. In this case, the native VLANs are different so although S1 will tag it as VLAN 1 it will be received by S2.


Q3. A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?

A. the OSPF route

B. the EIGRP route

C. the RIPv2 route

D. all three routes

E. the OSPF and RIPv2 routes

Answer: B

Explanation:

When one route is advertised by more than one routing protocol, the router will choose to use the routing protocol which has lowest Administrative Distance. The Administrative Distances of popular routing protocols are listed below:


Q4. Refer to the exhibit.

When running OSPF, what would cause router A not to form an adjacency with router B?

A. The loopback addresses are on different subnets.

B. The values of the dead timers on the routers are different.

C. Route summarization is enabled on both routers.

D. The process identifier on router A is different than the process identifier on router B.

Answer: B

Explanation:

To form an adjacency (become neighbor), router A & B must have the same Hello interval, Dead interval and AREA numbers


Q5. Refer to the exhibit.

Which WAN protocol is being used?

A. ATM

B. HDLC

C. Frame Relay

D. PPP

Answer: C

Explanation:

This question is to examine the show int command.

According to the information provided in the exhibit, we can know that the data link protocol used in this network is the Frame Relay protocol.

u201cLMI enq sentu2026u201d


Q6. A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)

A. informational

B. emergency

C. warning

D. critical

E. debug

F. error

Answer: B,D,F

Explanation:

The Message Logging is divided into 8 levels as listed below:

Level Keyword Description 0

emergencies System is unusable 1

alerts

Immediate action is needed 2

critical

Critical conditions exist 3

errors

Error conditions exist

4

warnings

Warning conditions exist 5

notification

Normal, but significant, conditions exist 6

informational Informational messages 7

debugging Debugging messages

If you specify a level with the u201cloggingtrap levelu201d command, that level and all the higher levels will be logged. For example, by using the u201clogging trap 3 command, all the logging of emergencies, alerts, critical, and errors, will be logged.


Q7. The network administrator cannot connect to Switch1 over a Telnet session, although the hosts attached to Switch1 can ping the interface Fa0/0 of the router.

Given the information in the graphic and assuming that the router and Switch2 are configured properly, which of the following commands should be issued on Switch1 to correct this problem?

A. Switch1(config)# line con0 Switch1(config-line)# password cisco Switch1(config-line)#login

B. Switch1(config)# interface fa0/1

Switch1(config-if)# ip address 192.168.24.3 255.255.255.0

C. Switch1(config)# ip default-gateway 192.168.24.1

D. Switch1(config)# interface fa0/1 Switch1(config-if)# duplex full

Switch1(config-if)# speed 100

E. Switch1(config)# interface fa0/1 Switch1(config-if)# switchport mode trunk

Answer: C

Explanation:

Since we know hosts can reach the router through the switch, we know that connectivity, duplex. Speed, etc. are good. However, for the switch itself to reach networks outside the local one, the ip default-gateway command must be used.


Q8. Which statement describes the process ID that is used to run OSPF on a router?

A. It is globally significant and is used to represent the AS number.

B. It is locally significant and is used to identify an instance of the OSPF database.

C. It is globally significant and is used to identify OSPF stub areas.

D. It is locally significant and must be the same throughout an area.

Answer: B

Explanation:

The Process ID for OSPF on a router is only locally significant and you can use the same number on each router, or each router can have a different number-it just doesn't matter. The numbers you can use are from 1 to 65,535. Don't get this confused with area numbers, which can be from 0 to 4.2 billion.


Q9. What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?

A. path cost

B. lowest port MAC address

C. VTP revision number

D. highest port priority number

E. port priority number and MAC address

Answer: A

Explanation:

The path cost to the root bridge is the most important value to determine which port will become the root port on each non-root switch. In particular, the port with lowest cost to the root bridge will become root port (on non-root switch).


Q10. What is the default administrative distance of OSPF?

A. 90

B. 100

C. 110

D. 120

Answer: C

Explanation:

Administrative distance is the feature that routers use in order to select the best path when there are two or more different routes to the same destination from two different routing protocols. Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value.

Default Distance Value Table

This table lists the administrative distance default values of the protocols that Cisco supports:

Route Source

Default Distance Values

Connected interface 0

Static route 1

Enhanced Interior Gateway Routing Protocol (EIGRP) summary route 5

External Border Gateway Protocol (BGP) 20

Internal EIGRP 90

IGRP 100 OSPF 110

Intermediate System-to-Intermediate System (IS-IS) 115

Routing Information Protocol (RIP) 120

Exterior Gateway Protocol (EGP) 140

On Demand Routing (ODR) 160

External EIGRP 170

Internal BGP 200

Unknown* 255


100% Most recent Cisco 200-125 Questions & Answers shared by 2passeasy, Get HERE: https://www.2passeasy.com//dumps/200-125/ (New 890 Q&As)