Exambibles Cisco 200-401 test serp provides each of our customers with all the real experience of using the actual exam. Numerous candidates have approved the Cisco 200-401 exam with all the help of our Cisco test materials. We provide complete refund if you dont pass the actual exam. And you merely need to supply your transcript and related forms. Our workers will remit your paying service fees to you soon. The ideal and outstanding quality and value pertaining to our Cisco exam guarantee you get the actual Cisco Cisco certification.

2021 Feb 200-401 thermostat:

Q31. - (Topic 2) 

An administrator has connected devices to an industrial switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this? 

A. Enable port security and use the keyword sticky. 

B. Set the switchport mode to trunk and save the running configuration. 

C. Use the switchport protected command to have the MAC addresses added to the configuration. 

D. Use the no switchport port-security command to allow MAC addresses to be added to the configuration. 

Answer: A 


Q32. - (Topic 2) 

Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration? 

A. Telnet encrypts only the login information, not the entire transmission. 

B. SSH requires fewer network resources and no additional configuration. 

C. Telnet is more difficult to use and configure than SSH. 

D. SSH encrypts the login and session information. 

Answer: D 


Q33. - (Topic 4) 

At which Layer would you use trace route to validate the path? 

A. Layer 1 

B. Layer 2 

C. Layer 3 

D. Layer 4 

Answer: C 


Q34. - (Topic 4) 

A network administrator has subnetted the 172.16.0.0 network using a subnet mask of 

255.255.255.192. A duplicate IP address of 172.16.2.120 has accidentally been configured on a workstation in the network. The technician on the plant floor must assign this workstation a new IP address within that same subnetwork. Which address should be assigned to the workstation? 

A. 172.16.1.80 

B. 172.16.2.80 

C. 172.16.1.64 

D. 172.16.2.64 

E. 172.16.2.127 

F. 172.16.2.128 

Answer: B 


Updated robertshaw 200-401:

Q35. - (Topic 1) 

Exhibit: 

Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3? 

A. the address of the switch interface that is connected to router interface Fa0/0 

B. the address of the switch interface that is connected to router interface Fa0/1 

C. the address of the host that is connected to Network A 

D. the address of the host that is connected to Network B 

E. the address of the router interface Fa0/0 

F. the address of the router interface Fa0/1 

Answer: E 


Q36. - (Topic 3) 

With what are APC connectors used? 

A. Category 6a cables that need tight radius bends 

B. copper network cables in corrosive environments 

C. single-mode fiber-optic cables to reduce return loss 

D. high-density copper patch panels 

Answer: C 


Q37. - (Topic 5) 

A router is not operating as expected and the network administrator wants to verify that the router booted using the correct IOS image. Which command should be used to determine which IOS is running on the router? 

A. show flash 

B. show version 

C. show memory 

D. show startup-config 

E. show config-register 

Answer: B 


Q38. - (Topic 5) 

What are two benefits that are provided by proper grounding and bonding systems? (Choose two.) 

A. higher speed communications 

B. safe discharge of electrostatic energy 

C. lower equipment power consumption 

D. equipotential.termination points for equipment and cable shields 

E. lowest carbon footprint 

Answer: B,D