It is impossible to pass Cisco 300-360 exam without any help in the short term. Come to Actualtests soon and find the most advanced, correct and guaranteed Cisco 300-360 practice questions. You will get a surprising result by our Renewal Designing Cisco Wireless Enterprise Networks practice guides.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 300-360 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 300-360 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/300-360-exam-dumps.html
2021 Apr 300-360 actual exam
Q1. When designing a WLAN, AP placement is important. Which option describes how to rank the density of APs needed to support location services versus data and voice services?
A. Data services have the lowest density of APs compared to location services, which has the highest density.
B. Data services have a lower density of APs compared to location services, but more than voice.
C. Voice services have the highest density of APs over location and data services.
D. Voice and data services require a higher density of APs than location services.
Answer: A
Q2. What is a common cause for signal attenuation?
A. Cinder block wall
B. Office window
C. Metal door
D. Glass wall
Answer: C
Q3. A hospital environment was designed to guarantee RF coverage at or better than -67 dBm in the 5 GHz spectrum. The customer mandates that RRM be used for DCA and TPC in both bands. After deployment, why do many of the legacy 802.11b/g devices have difficulty maintaining connectivity?
A. Excessive co-channel interference in the 2.4 GHz band exists.
B. Excessive overlapping channels in the 2.4 GHz band exists.
C. TPC drastically reduces Tx power in the 2.4 GHz band.
D. TCP drastically increases Tx power in the 2.4 GHz band.
Answer: C
Q4. An engineer must perform a survey where the target client devices range from standard
Wi-Fi-equipped laptops, consumer handhelds and tablets, and low power tracking tags limited to 12 mW Tx power. With which setting should the survey AP be configured?
A. local power 11
B. local power 5
C. local power 14
D. local power 8
Answer: B
Q5. A Cisco 7925 phone at a client’s location is not registering with CUCM. The engineer analyzes a packet capture, sees that the phone receives an IP, and downloads the proper configuration file from TFTP successfully. What type of messages should the phone be sending at this point?
A. H.245
B. H.323
C. MCGP
D. SCCP
Answer: D
Regenerate 300-360 exam question:
Q6. An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?
A. overlapping -72 dBm coverage from two access points
B. overlapping -67 dBm coverage from two access points
C. continuous -67 dBm coverage from one access point
D. continuous -72 dBm coverage from one access point
Answer: C
Q7. An engineer is planning for a 24 Mbps data rate for a new installation. What is the coverage area from the AP if the environment and other factors are not taken into consideration?
A. 225 feet
B. 80 feet
C. 150 feet
D. 100 feet
Answer: A
Q8. An engineer plugs in a Cisco Aironet 2700 Series Access Point and it is running in low power. Which three power requirements should be verified? (Choose three.)
A. 802.3ac compliant
B. 802.3at compliant
C. AP requires 43 VDC to function in full power.
D. AIR-PWRINJ3 power injector should be used.
E. AP requires 57 VDC to function in full power.
F. AIR-PWRINJ4 power injector should be used.
Answer: B,E,F
Explanation:
The access point should be powered by any 802.3at compliant device.
The recommended external power supply for the access point is the Cisco AIR-PWR-B power supply. The access point can also be powered by the following optional external power sources:
– Access point power injector (AIR-PWRINJ4)
– Any 802.3af compliant power injector is supported, but in this case the access point will dynamically shift from 3x4 to 3x3.
Reference: http://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getst art.html
Q9. Refer to the exhibit.
While testing the post-deployment WLAN network, you discover that an AP has been placed in a difficult area.
The AP cannot be moved easily because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.)
A. Add additional APs.
B. Increase the AP power level to maximum.
C. Rotate the AP 90 degrees to change antenna polarity.
D. Replace the AP with an AP and external antenna.
E. Change the AP location to one that is less RF hostile.
Answer: A,D
Q10. An engineer is deploying an outdoor Mesh network. Which four major factors should be considered? (Choose four.)
A. power
B. buildings
C. traffic lights
D. satellite dishes
E. line of sight
F. network connectivity
G. power lines
H. mounting
Answer: A,E,F,H