Your success in Cisco 300-615 is our sole target and we develop all our 300-615 braindumps in a way that facilitates the attainment of this target. Not only is our 300-615 study material the best you can find, it is also the most detailed and the most updated. 300-615 Practice Exams for Cisco Cisco Other Exam 300-615 are written to the highest standards of technical accuracy.
Free demo questions for Cisco 300-615 Exam Dumps Below:
NEW QUESTION 1
A network administrator attempts to install an application in the Cisco NX-OS Guest shell and receives an error that there is not enough space on the disk. Which command must the administrator run to increase the disk space available in the Guest shell?
- A. guestshell growdisk rootfs [size-in-MB]
- B. guestshell pvextend rootfs [size-in-MB]
- C. guestshell resize rootfs [size-in-MB]
- D. guestshell resize2fs rootfs [size-in-MB]
Answer: C
NEW QUESTION 2
Refer to the exhibit. Interface fc1/5 is offline. Which action should be taken to troubleshoot the issue?
- A. Activate the correct zoneset for VSAN 100.
- B. Update the FLOGI database to contain the FLOGI entries for interface fc1/5 in VSAN 100.
- C. Update the FCNs database to contain names for VSAN 100.
- D. Configure the upstream ports and the server ports to be in VSAN 100.
Answer: D
NEW QUESTION 3
DRAG DROP
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.
Select and Place:
- A. Mastered
- B. Not Mastered
Answer: A
Explanation: 
NEW QUESTION 4
Refer to the exhibit. After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational primary role back to Switch-A? (Choose two.) A. Configure the local vPC role priority to have a lower value than Switch-A.
- A. Configure the local vPC role priority to have a higher value than Switch-A.
- B. Disable and then re-enable the vPC peer-keepalive link.
- C. Configure the local vPC role priority to have the same value as Switch-A.
- D. Disable and then re-enable the vPC peer link.
Answer: BE
NEW QUESTION 5
Refer to an exhibit. An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?
- A. Save the system image in NVRAM.
- B. Use the same system image as the kickstart image.
- C. Load a new system image.
- D. Reload the same system image.
Answer: C
NEW QUESTION 6
A customer configures HSRP between two data centers that are interconnected with OTV. The configuration succeeds, but traffic between two ESXi virtual hosts on the same site is routed suboptimally through the OTV overlay. Which two actions optimize the traffic? (Choose two.)
- A. Disable first-hop redundancy.
- B. Filter HSRP traffic by using a Layer 3 VACL on the OTV edge devices.
- C. Filter HSRP by using a Layer 2 MAC-list on the ESXi vSwitch.
- D. Filter HSRP traffic by using a Layer 3 VACL on the ESXi vSwitch.
- E. Filter HSRP by using a Layer 2 MAC-list on the OTV edge devices.
Answer: AB
NEW QUESTION 7
Refer to the exhibit. The HSRP configuration in the exhibit fails to function. Which action resolves this issue?
- A. Enable IP redirects.
- B. Set the MTU to 1500 bytes.
- C. Configure HSRP version 2.
- D. Configure the same HSRP group on both devices.
Answer: A
NEW QUESTION 8
Refer to the exhibit. Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?
- A. Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.
- B. Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.
- C. Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.
- D. Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.
Answer: B
NEW QUESTION 9
Refer to the exhibit. When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?
- A. Port 15 is configured as an Ethernet port.
- B. Port 15 is configured for 4-Gb FC.
- C. Port 15 is missing a license.
- D. The polarity of the fiber cable is reversed.
Answer: B
NEW QUESTION 10
Refer to the exhibit. Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?
- A. Acknowledge the primary fabric interconnect.
- B. Remove the service pack from the subordinate fabric interconnect.
- C. Clear the startup version of the default infrastructure pack.
- D. Upgrade the firmware of the infrastructure firmware by using the force option.
Answer: C
NEW QUESTION 11
An engineer discovers that an NPV/NPIV uplink experiences a heavy load and plans to add more uplinks. Which statement about what occurs when the new uplinks are added is true?
- A. Only new connections use the new uplinks automatically.
- B. Paths must be defined before new connections can use the new uplinks.
- C. All connections must be reset before the new uplinks can be used.
- D. New and existing connections use the new uplinks automatically.
Answer: D
NEW QUESTION 12
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?
- A. Verify that the SFPs are supported.
- B. Change the SFP to operate at 4 Gbps instead of 2 Gbps.
- C. Run the shutdown and then no shutdown command on the interface.
- D. Run the switchport ignore bit-errors command on the interface.
Answer: D
NEW QUESTION 13
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?
- A. Modify the VLAN assignment to vNICs.
- B. Change the PIN groups on the vHBAs.
- C. Modify the FCoE VLAN.
- D. Set the FCoE VLAN as the native VLAN on server uplinks.
Answer: A
NEW QUESTION 14
A server administrator attempts to change the Cisco IMC KVM certificate to one signed by a private CA, but the certificate is not being accepted. What can cause this process to fail?
- A. using a certificate with a password-protected private key
- B. RSA encryption being used in the generation of the certificate.
- C. AES encryption being used in the generation of the certificate.
- D. public IP addres of the Cisco IMC not being included in the SAN.
Answer: A
NEW QUESTION 15
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)
- A. M-Series module
- B. ESSENTIALS license
- C. STORAGE-ENT license
- D. FCoE license
- E. F-Series module
Answer: DE
NEW QUESTION 16
After upgrading a client’s fabric interconnect to the latest version, an engineer discovers that the appliance has lost its entire configuration. Which two locations should an engineer check to confirm that the appliance had backed up the configuration prior to the upgrade in order to retrieve the lost configuration? (Choose two.)
- A. Equipment FSM page, InternalBackup stage
- B. Service profiles page, InternalBackup stage
- C. Admin page, PollInternalBackup stage
- D. Equipment FSM page, PollInternalBackup stage
- E. Admin page, InternalBackup stage.
Answer: AC
NEW QUESTION 17
Refer to the exhibit. A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch. The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?
- A. Replace the SFP port module in fc2/10.
- B. Configure the admin port type E on the upstream switch that connects the port.
- C. Enable NPIV on the upstream switch that connects the port.
- D. Configure the BB_credit buffers on the upstream switch that connects the port.
Answer: C
NEW QUESTION 18
A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)
- A. Load an uncorrupt bootloader image.
- B. Load an uncorrupt kickstart image.
- C. Reconnect L1/L2 cables between the Fis.
- D. Reformat the fabric interconnect.
- E. Load the correct version of the boot image.
Answer: BE
NEW QUESTION 19
Refer to the exhibit. The EEM script fails to send an SNMP trap when a user attempts to enter configuration mode. Which configuration is missing from the script?
- A. event statement
- B. event-default action statement
- C. policy-default action statement
- D. IP address of the SNMP server
Answer: D
NEW QUESTION 20
An engineer is troubleshooting a custom AV pair that was created by a client on an external authentication server to map a read-only role for a specific security domain. Which AV pair solves the problem?
- A. shell:domains=Security_Domain_1//Read_Role_1|Read_Role_2
- B. shell:domains=Security_Domain_1/Write_Role_1|Read_Role_2
- C. shell=Security_Domain_1/Read_Role_1|Read_Role_2
- D. shell:domains=Security_Domain_1/Read_Role_1|Read_Role_2
Answer: A
NEW QUESTION 21
An engineer is troubleshooting a packet flow from an access leaf to spine. Which EVPN routes are expected on this connection?
- A. EVPN Type 1-5
- B. EVPN Type 0,9,15
- C. EVPN Type 9-15
- D. EVPN Type 0,16
Answer: A
NEW QUESTION 22
......
P.S. Easily pass 300-615 Exam with 0 Q&As Dumpscollection.com Dumps & pdf Version, Welcome to Download the Newest Dumpscollection.com 300-615 Dumps: https://www.dumpscollection.net/dumps/300-615/ (0 New Questions)