♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 400-101 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 400-101 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/400-101-exam-dumps.html
Q461. Which three options are best practices for implementing a DMVPN? (Choose three.)
A. Use IPsec in tunnel mode.
B. Implement Dead Peer Detection to detect communication loss.
C. Configure AES for encryption of transported data.
D. Configure SHA-1 for encryption of transported data.
E. Deploy IPsec hardware acceleration to minimize router memory overhead.
F. Configure QoS services only on the head-end router.
Answer: A,B,C
Explanation:
Best Practices Summary for Hub-and-Spoke Deployment Model
This section describes the best practices for a dual DMVPN cloud topology with the hub-and-spoke deployment, supporting IP multicast (IPmc) traffic including routing protocols.
The following are general best practices:
. Use IPsec in transport mode
. Configure Triple DES (3DES) or AES for encryption of transported data (exports of encryption algorithms to certain countries may be prohibited by law).
Implement Dead Peer Detection (DPD) on the spokes to detect loss of communication between peers.
. Deploy hardware-acceleration of IPsec to minimize router CPU overhead, to support traffic with low latency and jitter requirements, and for the highest performance for cost.
. Keep IPsec packet fragmentation to a minimum on the customer network by setting MTU size or using Path MTU Discovery (PMTUD).
. Use Digital Certificates/Public Key Infrastructure (PKI) for scalable tunnel authentication.
. Configure a routing protocol (for example, EIGRP, BGP or OSPF) with route summarization help alleviate interface congestion issues and to attempt to keep higher priority traffic from being dropped during times of congestion.
Reference: http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/DMVPDG/DMV PN_1.html
Q462. DRAG DROP
Drag and drop the IPv6 prefix on the left to the correct address type on the right.
Answer:
Q463. Which technology can be affected when switches are used that do not support jumbo frames?
A. 802.1x
B. BFD
C. OSPFv3
D. 802.1q
Answer: D
Explanation:
The 802.1Q tag is 4 bytes. Therefore, the resulting Ethernet frame can be as large as 1522 bytes. If jumbo frames are not supported, then typically the MTU on an Ethernet link needs to be lowered to 1496 to support this extra 802.1Q tag.
Q464. Refer to the exhibit.
Which configuration is missing that would enable SSH access on a router that is running Cisco IOS XE Software?
A. int Gig0/0/0
management-interface
B. class-map ssh-class
match access-group protect-ssh
policy-map control-plane-in
class ssh-class
police 80000 conform transmit exceed drop
control-plane
service-policy input control-plane-in
C. control-plane host
management-interface GigabitEthernet0/0/0 allow ssh
D. interface Gig0/0/0
ip access-group protect-ssh in
Answer: C
Explanation:
The feature Management Plane Protection (MPP) allows an administrator to restrict on which interfaces management traffic can be received by a device. This allows the administrator additional control over a device and how the device is accessed. This example shows how to enable the MPP in order to only allow SSH and HTTPS on the GigabitEthernet0/1 interface:
!
control-plane host
management-interface GigabitEthernet 0/1 allow ssh https
!
Reference: http://www.cisco.com/c/en/us/support/docs/ip/access-lists/13608-21.html
Q465. A configuration includes the line ip nbar port-map SSH tcp 22 23 443 8080. Which option describes the effect of this configuration line?
A. It configures NBAR to search for SSH using ports 22, 23, 443, and 8080.
B. It configures NBAR to allow SSH connections only on ports 22, 23, 443, and 8080.
C. It enables NBAR to inspect for SSH connections.
D. It creates a custom NBAR port-map named SSH and associates TCP ports 22, 23, 443, and 8080 to itself.
Answer: A
Explanation:
The ip nbar-port-map command configures NBAR to search for a protocol or protocol name using a port number other than the well-known port.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/qos/command/reference/fqos_r/qrfcmd10.pd f
Q466. Which statement about SSHv2 is true?
A. Routers acting as SSH clients can operate without RSA keys.
B. SSHv2 supports port forwarding and compression.
C. The RSA key pair size must be at least 512.
D. You must configure a default gateway before you enable SSHv2.
Answer: A
Q467. In which two situations is an EIGRP hello packet sent as unicast? (Choose two.)
A. during neighbor discovery
B. when link costs change
C. when the neighbor command is used
D. when an ACK is sent
Answer: C,D
Q468. Which ICMP message type is used to assist path MTU discovery?
A. destination unreachable
B. redirect message
C. source quench
D. time exceeded
Answer: A
Q469. Which two statements about the assert process in LAN-based PIM are true? (Choose two.)
A. If the metrics are the same, the router with the lowest advertised routing protocol metric for that route is elected.
B. If the metrics are the same, the router with the highest IP address on the LAN is elected.
C. If the metrics are the same, the router with the highest advertised routing protocol metric for that route is elected.
D. If the metrics are the same, the router with the lowest IP address on the LAN is elected.
Answer: A,B
Q470. You are installing a new device to replace a device that failed. The configuration of the failed device is stored on a networked server, and the new device has an RXBOOT image installed. Under which condition does the streamlined Setup mode fail?
A. The last four bits of the configuration register are not equal to the decimal value 0 or 1.
B. The startup configuration file was deleted.
C. Bit 6 is set in the configuration register.
D. The startup configuration is corrupt.
Answer: A
Explanation:
The lowest four bits of the configuration register (bits 3, 2, 1, and 0) form the boot field. The boot field determines if the router boots manually, from ROM, or from Flash or the network. To change the boot field value and leave all other bits set to their default values, follow these guidelines:
. If you set the configuration register boot field value to 0x0, you must boot the operating system manually with the boot command.
. If you set the configuration register boot field value to 0x1, the router boots using the default ROM software.
. If you set the configuration register boot field to any value from 0x2 to 0xF, the router uses the boot field value to form a default boot filename for booting from a network server. For more information about the configuration register bit settings and default filenames, refer to the appropriate router hardware installation guide.
Reference: http://www.cisco.com/c/en/us/td/docs/ios/12_2/configfun/command/reference/ffun_r/frf010. html