Want to know Pass4sure 642-035 Exam practice test features? Want to lear more about Cisco Troubleshooting Cisco Data Center Unified Computing certification experience? Study Top Quality Cisco 642-035 answers to Replace 642-035 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 642-035 (Troubleshooting Cisco Data Center Unified Computing) test on your first attempt.
♥♥ 2021 NEW RECOMMEND ♥♥
Free VCE & PDF File for Cisco 642-035 Real Exam (Full Version!)
★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions
Free Instant Download NEW 642-035 Exam Dumps (PDF & VCE):
Available on:
http://www.surepassexam.com/642-035-exam-dumps.html
Q1. Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.)
A. BIOS
B. Cisco UCS Manager
C. I/O module
D. Cisco IMC
E. fabric interconnect
F. adapter
G. board controller
Answer: AFG
Q2. A customer is configuring VSANs in a Cisco UCS domain. After configuring the VSANs 3840, 3841, and 3842 in FC end-host mode, the customer sees that these VSANs are not operational and that Cisco UCS Manager is raising faults. What is the cause of this problem?
A. VSANs 3840, 3841, and 3842 should be in the allowed list on the trunk to clear the fault.
B. VSANs 3840 to 4079 cannot be used in Fibre Channel end-host mode in a Cisco UCS domain.
C. The fabric interconnect needs to be configured in switching mode and the VSANs need to be allowed on the trunk.
D. Use the UCS CLI to clear the fault on the VSAN trunk to forward the VSANs with faults.
Answer: B
Q3. A local storage installation of ESX on a Cisco UCS C-Series server has failed due to local storage issues. What is the cause of the problem?
A. LSI drivers are not bundled with ESX.
B. The hard drive has a 1-TB partition size.
C. The server only has an onboard controller, while ESX requires an LSI RAID controller card.
D. ESX is not supported on Cisco UCS C-series servers.
Answer: C
Q4. Which actions on a Cisco UCS Server can be performed under the Cisco IMC utilities? (Choose Four.)
A. export tech support information to a remote host
B. download a tech support file locally
C. reboot the Cisco IMC
D. recover a corrupt BIOS
E. install firmware updates
Answer: ABCD
Q5. A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and
after the service profile association and the server does not boot. What is the cause of this problem?
A. RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.
B. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.
C. The server needs to be booted via SAN in cluster migration to support RAID1.
D. The Cisco UCS B-Series blade server has older firmware that needs to be updated first.
Answer: B
Q6. You are attempting to install Microsoft Server 2008 R2 on a Fibre Channel LUN, but the installer does not see the LUN. You have used F6 to load the appropriate SCSI driver. What should your first troubleshooting step be?
A. Email the SAN administrator to validate that your LUN is defined.
B. Check the configuration of the vHBA in the service profile.
C. Validate that the boot order is correct.
D. Validate zoning on the Fibre Channel switch.
E. Validate that the Fibre Channel uplink from the fabric interconnect is up.
Answer: B
Q7. UCS-A# scope eth-uplink UCS-A /eth-uplink
# scope fabric a UCS-A /eth-uplink/fabric
# scope interface 2 3 UCS-A /eth-uplink/fabric/interface
# create mon-src Monitor23 UCS-A /eth-uplink/fabric/interface/mon-src*
# set direction receive UCS-A /eth-uplink/fabric/interface/mon-src* # commit-buffer
What does the command scope interface 2 3 in the above CLI command sequence do on a Cisco UCS blade server?
A. enters the interface command mode for the specified uplink port
B. enters the interface command mode for the specified Fabric A
C. enters the interface command mode for the specified Fabric B
D. enters slot 3 port 2 specified uplink port
Answer: A
Q8. How does the FSM react after an error or timeout at a stage?
A. stops
B. retries until successful
C. continues
D. retries that stage at scheduled intervals
E. raises faults and continues
Answer: D
Q9. Refer to the exhibit.
Which type of power policy is shown when referring to a Cisco UCS environment?
A. chassis
B. blade server
C. fabric interconnect
D. global
E. switch
Answer: D
Q10. Refer to the exhibit.
Which of these is an extension of the virtual machine abstraction that is applied to physical servers?
A. service profile
B. compute profile
C. organization profile
D. locale profile
E. role profile
Answer: A