Our Cisco 642-035 simulated tests contain every little thing you will encounter inside the real exam. Examcollections That professionals are committed to making the most precise and also original Cisco Cisco practice questions and also answers which are created with higher standards associated with accuracy. All the 642-035 training materials are presented inside Pdf files and Analyze Engine software. Youll be able to download them on your PC for no cost. Pdf files are printable and also portable and the analyze engine are downloadable.
2021 Dec 642-035 certification:
Q21. What is the recommended procedure to update Cisco UCS C-Series rack-mount server firmware?
A. Launch the Cisco UCS Firmware Update Utility from virtual media.
B. Launch the Cisco UCS Host Update Utility from virtual media.
C. Launch the Cisco UCS Server Update Utility from virtual media.
D. Launch the Cisco UCS CIMC Update Utility from virtual media.
Answer: B
Q22. A customer is trying to boot an operating system that is installed on the eUSB on a Cisco UCS B-Series blade server; however, the boot fails. What is the cause of this failure?
A. The local disk must be the first device in the boot order.
B. eUSB is not a supported boot device.
C. eUSB support is available only on the Cisco UCS C-Series rack server.
D. eUSB is not the first device in the boot order for the server.
Answer: D
Q23. If a server is not associated with a service profile, the activated firmware remains pending. Which two steps should you take? (Choose two.)
A. Manually reboot the server.
B. Reset the server to a new profile.
C. Reset the unassociated server to activate the firmware.
D. Reinitialize the firmware process with Cisco UCS Manager.
E. Download the firmware and start over.
F. Shut down gracefully and start over.
Answer: AC
Q24. How long are the LED states saved after a blade is removed from a Cisco UCS chassis?
A. 1 minute
B. 5 minutes
C. 10 minutes
D. 30 minutes
E. 60 minutes
Answer: C
Q25. Refer to the exhibit.
In a Cisco UCS environment, which switch mode does the exhibit portray?
A. end host mode
B. switching mode
C. access mode
D. core mode
Answer: A
Latest 642-035 exam:
Q26. Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.)
A. BIOS
B. Cisco UCS Manager
C. I/O module
D. Cisco IMC
E. fabric interconnect
F. adapter
G. board controller
Answer: AFG
Q27. A customer is configuring VSANs in a Cisco UCS domain. After configuring the VSANs 3840, 3841, and 3842 in FC end-host mode, the customer sees that these VSANs are not operational and that Cisco UCS Manager is raising faults. What is the cause of this problem?
A. VSANs 3840, 3841, and 3842 should be in the allowed list on the trunk to clear the fault.
B. VSANs 3840 to 4079 cannot be used in Fibre Channel end-host mode in a Cisco UCS domain.
C. The fabric interconnect needs to be configured in switching mode and the VSANs need to be allowed on the trunk.
D. Use the UCS CLI to clear the fault on the VSAN trunk to forward the VSANs with faults.
Answer: B
Q28. You successfully install VMware ESXi 5.0 U1 on a Cisco UCS B200 M3 server to a Fibre Channel LUN. When you reboot the server, you see the message "Reboot and Select Proper Boot device or insert Boot Media in selected Boot device and press a key." What are the first two pieces of information you should gather to troubleshoot the boot failure? (Choose two.)
A. Connect to the NX-OS shell via the CLI and run the show npv flogi-table command.
B. SSH to the MDS 9124 and run the show flogi database command.
C. Validate the boot target WWPN and LUN ID in the service profile.
D. Validate the correct source WWPN in the service profile vHBA definition.
E. Validate zoning for your WWPN on the Cisco MDS 9124.
F. Validate that the boot order indicates the vHBA as the first device.
G. Ensure LUN masking is correctly configured on the storage controller.
Answer: CF
Q29. The Cisco UCS Manager displays FSM information for which four of these? (Choose four.)
A. which FSM task is being executed
B. the current state of an FSM task
C. the status of the previous FSM task
D. any error codes returned while processing E. all completed FSM tasks
F. multiple FSM tasks that completed over multiple tries
G. multiple FSM tasks that failed
Answer: ABCD
Q30. Refer to the exhibit.
Which mistake did the UCS administrator make when trying to access the GUI?
A. specified the incorrect login domain B. did not use the VIP
C. tried to login before the GUI had fully booted up
D. password is incorrect
E. attempted to login to the subordinate cluster peer
Answer: E