Ucertify provides you with total training based on the Cisco Cisco most recent syllabus. Clear your current Cisco exam with our precise and reliable practice questions and answers. The Cisco 642-732 products will likely be available right away in free downloadable Pdf format along with test serp after all of us confirm your payment. By practicing the comprehensive Cisco 642-732 exam dumps in Ucertify, you are guaranteed to have through the Cisco exam in first attempt.

2021 Nov 642-732 cuwss pass4sure:

Q81. Which two factors influence the density of APs in a data-only WLAN environment? (Choose two.) 

A. Channel reuse and WLAN bandwidth 

B. The type of controller chosen. 

C. The defined coverage area and customer needs. 

D. The number of clients that will roam through the facility. 

E. The number of APs dedicated to voice services. 

Answer: A,C 


Q82. Which wireless tool would be most useful in planning a WLAN solution prior to performing a site survey? 

A. Ekahau Survey 

B. Air Magnet Survey 

C. Air Magnet Wi-Fi Analyzer 

D. Cisco Spectrum Expert 

E. Cisco WCS 

Answer: E 


Q83. An engineer installed a 1252 AP and is getting power from the switch. However, devices connected to the wireless network cannot get 802.11n data rates. What supported switchport protocol or standard could be the reason for this? 

A. 802.3af 

B. 802.3at 

C. 802.1p 

D. 802.11e 

Answer: A 


Q84. Which two options describes the vertical RF coverage pattern of an antenna? (Choose two.) 

A. View from the side 

B. View from above 

C. Azimuth 

D. H-plane 

E. E-plane 

Answer: A,E 


Q85. In performing a post-deployment audit, you are concerned by significant changes in measured RSSI and SNR values taken on a wireless client in one location. How do you explain the differences in these values? 

A. The differences in the RSSI and SNR values are a result of signal diffusion in the environment. 

B. The differences in the RSSI and SNR values are a result of multipath in the environment. 

C. The differences in the RSSI and SNR values are a result of signal absorption in the environment. 

D. The differences in the RSSI and SNR values are a result of signal diffraction in the environment. 

Answer: B 


Rebirth 642-732 cuwss exam:

Q86. When performing a post-installation audit with a auditing tool such as Ekahau, which two steps are associated with the active portion of the audit? (Choose two.) 

A. Check that all channels are supported by the APs regardless of client capabilities. 

B. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel. 

C. Verify that the network traffic of physical data rate and packet loss meets user requirements. 

D. Verify smooth roaming. 

E. Check to see if the signal level on other access points that are heard on the same channel is at least 19 dBm weaker than the access point that you are next to. 

Answer: C,D 


Q87. You have been contacted by a medium-sized hospitality company that has 50 hotels. They would like to upgrade their existing WLAN in each hotel to 802.11n. While performing the site surveys for each hotel, what are the issues that you need to take into consideration when determining the locations for each AP? 

A. Selecting AP locations where power is already available 

B. Selecting APs that can be hidden in ceiling panels to provide a secure and clean aesthetic look 

C. Selecting locations that are easily accessed so maintenance and upgrades can be performed quickly 

D. Selecting locations that make visual assessment of the AP operation easy 

Answer: B 


Q88. When performing a post-installation audit using the Ekahau Survey tool, which four steps are associated with the passive portion of the audit? (Choose four.) 

A. Check that all channels are supported by the APs regardless of client capabilities. 

B. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel. 

C. Verify that the real-world network traffic (for example, physical data rate, packet loss, etc.) meets user requirements. 

D. When you have completed the post-installation surveys, compare them to the surveys that were performed before the installation. They should look nearly identical. 

E. Check to see if the signal levels on other access points that are heard on the same channel are at least 19 dBm weaker than the access point that you are next to. 

F. Survey by SSID to ensure that smooth roaming is taking place. 

Answer: A,B,D,E 


Q89. Refer to the exhibit. 

In testing the post-deployment WLAN network you have discovered an AP that has been placed in a difficult area. The AP cannot be easily moved because of various requirements. The client performance of various Apple and Microsoft operating system-based products does not meet expectations. Which two options can help mitigate the performance issue? (Choose two.) 

A. Add additional APs. 

B. Replace the AP with an AP and external antenna. 

C. Increase the AP power level to maximum. 

D. Change the AP location to one that is less RF hostile. 

E. Rotate the AP 90 degrees to change antenna polarity. 

Answer: A,B 


Q90. When using WCS 7.0 to calibrate a floor in a facility, which two factors are common to the point and linear calibration methods? (Choose two.) 

A. You must go through each collection point at a speed that isn't too fast to collect too much information nor too slow which limits the amount of information collected. 

B. You must sample both the 802.11a/n and the 802.11b/g/n network separately. 

C. If one collection point in the linear or point collection method is missed, you have to start at the beginning again. 

D. Rotating the client is only required during the point collection process because the linear method is a slowly moving process. 

E. You will only need to combine the linear and point collection methods in special spaces like hallways. 

Answer: A,B