Refined of 642-732 exam topics materials and free samples for Cisco certification for candidates, Real Success Guaranteed with Updated 642-732 pdf dumps vce Materials. 100% PASS CCNP Wireless - CUWSS exam Today!
2021 Nov 642-732 cuwss study guide:
Q21. You have a multinational customer that would like you to perform a wireless site survey for a new manufacturing facility in Singapore. They have had a local vendor install a point-to-point wireless bridge link between two buildings 1 km apart. The ground between the buildings is flat but because facilities are in the mountains, dense fog is an issue. There are no line of sight issues between the buildings. The link is experiencing errors and throughput issues. Currently the two radios are set to operate at 2.4 GHz and the transmit power is set to 7 dBm with 7 dBm antennas. What do you need to take into consideration when performing the site survey for this link?
A. Change the radio power to 17 dBm.
B. Change the radio power to 20 dBm and replace with a 16 dBm antenna.
C. Change the radio power to 29 dBm.
D. Change the radio power to 13 dBm.
Answer: D
Q22. A company needs to link two buildings, separated by 100 feet of parking lot, with Cisco 1300 bridges. Which three Cisco recommended antennas should be used? (Choose three.)
A. AIR-ANT5959
B. AIR-ANT1949
C. AIR-ANT1728
D. AIR-ANT24120
E. AIR-ANT2506
F. AIR-ANT2410Y-R
Answer: B,E,F
Q23. Refer to the exhibit. Which type of interference would the engineer detect on the Cisco Spectrum Expert?
A. Bluetooth
B. Wi-Max
C. DECT phone
D. microwave
E. analog camera
Answer: D
Q24. Refer to the exhibit.
Which type of cable connector is displayed that is used to connect antennas to transmitters?
A. RP-TNC
B. N
C. SMA
D. SMB
E. MMCX
Answer: B
Q25. Refer to the exhibit.
What is the most likely cause of MAP1 association to MAP2 instead of directly to the RAP?
A. Incorrect BGN
B. Default BGN
C. SNR
D. Absorption and scattering caused by weather conditions.
E. Incorrect radio configuration
Answer: C
Far out 642-732 official certification guide:
Q26. Refer to the exhibit.
After performing a Layer 1 survey using Cisco Spectrum Expert, what is the result indicated by the visual screen?
A. Normal 802.11b activity
B. Normal 802.11g activity
C. Microwave oven interference
D. Video camera interference
E. Bluetooth device interference
Answer: A
Q27. Refer to the exhibit. A company requires a multi-point bridge solution with Cisco 1400 series bridges. The central bridge (B1) is set to 10 dBm, the manufacturing remote bridge (B2) is set to 20 dBm, the inventory remote bridge (B3) is set to 20 dBm, and the shop remote bridge (B4) is set to 10 dBm. What is the maximum allowed power setting for all four bridges?
A. B1=12dBm B2=12dBm B3=12dBm B4=12dBm
B. B1=12dBm B2=24dBm B3=24dBm B4=24dBm
C. B1=24dBm B2=12dBm B3=12dBm B4=12dBm
D. B1=24dBm B2=24dBm B3=24dBm B4=24dBm E. B1=20dBm B2=20dBm B3=20dBm B4=20dBm
F. B1=10dBm B2=24dBm B3=24dBm B4=24dBm
Answer: B
Q28. How would clients react to a controller configuration that utilized unsupported channels?
A. Unsupported channels can cause coverage holes for clients as well as limit their connectivity.
B. Unsupported channels would be ignored by clients.
C. Unsupported channels would have no impact on clients. The user would simply need to roam to a supported channel.
D. Unsupported channels are not configurable on the controller, thus there would be no impact on clients.
Answer: A
Q29. DRAG DROP
Answer:
Q30. Which item is more of an issue to outdoor wireless mesh deployment than indoor?
A. Reflection
B. Scattering
C. Absorption
D. Delay spread
Answer: D