We provide real 352-001 exam questions and answers braindumps in two formats. Download PDF & Practice Tests. Pass Cisco 352-001 Exam quickly & easily. The 352-001 PDF type is available for reading and printing. You can print more and practice many times. With the help of our Cisco 352-001 dumps pdf and vce product and material, you can easily pass the 352-001 exam.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 352-001 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 352-001 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/352-001-exam-dumps.html

Q81. Refer to the exhibit. 

What limitations exist in this design, given that the access layer devices are expected to steadily increase by two devices per week for the next year? 

A. scalability 

B. serviceability 

C. redundancy 

D. resiliency 

Answer: A 


Q82. An IBGP mesh design is being scoped, and in the discussions, one of the design engineers proposes the use of route reflectors. Which limitation is valid when using route reflectors in this design? 

A. The configuration complexity on the routers will be increased. 

B. Route reflectors will limit the total number of routes in the topology. 

C. Multipath information is difficult to propagate in a route reflector topology. 

D. Route reflectors will cause an opportunity to create routing loops. 

Answer: C 


Q83. You have been asked to design a wireless network solution that will implement context-aware services on an existing network that was initially deployed for data traffic only. Which two design principles would you follow to increase the location accuracy with the least possible impact on the current setup? (Choose two.) 

A. Use directional antennas to provide better cell separation. 

B. Add access points along the perimeter of the coverage area. 

C. Install additional APs in monitor mode where the cochannel interference would otherwise be affected. 

D. Increase the AP density to create an average interaccess point distance of less than 40 ft. 

E. Fine tune the access points radio configuration to have a higher average transmission power to achieve better coverage. 

Answer: BC 


Q84. You are designing a large Frame Relay WAN for a customer. The routing protocol is OSPF. What is the effect on the routing table if the WAN interfaces are configured as point-to-multipoint? 

A. Only a route for the DR will be present in the routing table. 

B. Configuring point-to-multipoint has no effect on the routing table. The route that is configured with the area command will be seen in the routing table. 

C. Multipoint interfaces dynamically add the network of the connected interface. 

D. Multipoint interfaces dynamically add a /32 route for each neighbor in the WAN. 

Answer: D 


Q85. You are designing an Out of Band Cisco Network Admission Control, Layer 3 Real-IP Gateway deployment for a customer. Which VLAN must be trunked back to the Clean Access Server from the access switch? 

A. untrusted VLAN 

B. user VLAN 

C. management VLAN 

D. authentication VLAN 

Answer: A 


Q86. You work for a large company that has just acquired another smaller company. You have been asked to lead a group of SAN experts from both companies to design the integration plan that will be used to interconnect the SANs and migrate the data from the newly acquired company to the main storage arrays. The first thing that the team discovers is that the two SANs have the same domain IDs. 

As the SAN team lead, what would you advise your team to do so that you can interconnect the two SANs while minimizing disruption? 

A. Use FCIP with Write Acceleration and IVR version 1 with a transit VSAN to expedite the data transfer between the two SANs. 

B. Change the domain IDs on both SANs so that they are both unique and then connect ISLs between the SANs. 

C. Use IVR NAT with a transit VSAN between the SANs. 

D. The two SANs cannot be merged without disruption. 

Answer: C 


Q87. A junior engineer is implementing one of your optical designs and asks about CWDM (Coarse Wavelength Division Multiplexing). Which two features describe CWDM? (Choose two.) 

A. typically used over long distances, but requires optical amplification 

B. allows up to 32 optical carriers to be multiplexed onto a single fiber 

C. shares the same transmission window as DWDM 

D. uses the 850-nm band 

E. Passive CWDM devices require no electrical power. 

Answer: CE 


Q88. You are designing an 802.11 wireless network to include a controller as a central configuration point and access points across several remote sites. Which two aspects will manage the flow of the traffic to meet these design considerations? (Choose two.) 

A. WLAN local switching with VLAN mapping requires that VLAN ID that is mapped on the AP to match a dynamic interface that is configured on the wireless LAN controller. 

B. Layer 3 roaming is not supported for locally switched WLANs. 

C. The 802.1x authentication for a client associated to an AP on a locally switched WLAN is always handled at the wireless LAN controller side. 

D. The access point can receive multicast traffic in the form of multicast packets from the WLC. 

E. WLAN access lists can be applied only to centrally switched WLANs. 

Answer: BE 


Q89. Tesla Radio GmbH is going to build a new research lab network based on a set of switches that would connect to their existing enterprise network. They are considering a design that would guarantee loop-free behavior within the set of switches. The design would also allow the group of switches to seem like a single switch to the enterprise network, because it is owned by a separate administrative group. Which Spanning Tree Protocol should be used to support the design requirements? 

A. IEEE 802.1w 

B. IEEE 802.1D 

C. IEEE 802.1s 

D. IEEE 802.1p 

Answer: C 


Q90. In an OSPF network, users in a particular OSPF non-backbone area are complaining about slow access speeds to a shared corporate resource in another OSPF area. Traceroutes show that theusers are taking a suboptimal default route to the destinations. Which solution will improve access speed? 

A. Make the area totally stubby so that the default can be followed along the best path. 

B. Create a virtual link between the areas so that traffic can shortcut directly between them. 

C. Implement policy routing to channel the traffic in the optimal direction. 

D. Leak specific summaries on the ABRs for the remote subnets in addition to the default. 

Answer: D