When you are planning to get the actual Cisco Cisco certification but will not know the best way to prepare regarding it, Actualtests may offer an individual an absolute best and rapid way. Weve a mass of Cisco 642-732 exam brain dumps. With our Cisco 642-732 training course, you may get all the 642-732 important contents. Actualtestss Cisco 642-732 exam questions along with answers are gathered by thousands of successful certified professionals round the globe. You will have a full spectrum with the Cisco 642-732 actual examination. Master all the crucial topics of the Cisco preparation components, you are ensured to pass the real exam.
2021 Nov cisco 642-732 exam:
Q51. Which three are logistical issues that need to be taken into consideration prior to performing a site survey? (Choose three.)
A. What level of client density and throughput is expected for each WLAN cell?
B. Will security clearances be required to perform the site survey?
C. How much time will be required to survey each potential AP location?
D. Will contractor badges and employee or union escorts be required while performing the site survey?
E. Is access available to customer employees so initial interviews can be performed?
F. Will any facility orientation be required prior to performing the site survey?
Answer: B,D,F
Q52. Which three types of information should be included in the post-installation customer report? (Choose three.)
A. VLAN structure and naming convention
B. Throughput and dB loss for all fiber-optic backbone connections
C. Naming convention for APs and controllers
D. Reachability status for all WLAN clients and tags
E. The number of licenses consumed by clients and tags at installation
F. Any locations in the WLAN coverage that are secure and require special access
Answer: A,C,E
Q53. Refer to the exhibit.
The signal is being degraded to the point of link drops. You have examined the roof and the visual sighting of the remote antenna. What could be causing the issue?
A. The receiving antenna is too close to the transmitting antenna.
B. The first Fresnel zone is more than 60% blocked by the parapet.
C. The visual line of sight is more than 60% blocked by the parapet.
D. The cable between the APs and the antennae is introducing too much loss.
E. The roof material is absorbing too much of the signal.
Answer: B
Q54. What is the minimum CCX version necessary on a client when adding data points during WCS Calibration?
A. CCXv1
B. CCXv2
C. CCXv3
D. CCXv4
E. CCXv5
Answer: B
Q55. What is a typical attenuation value for a cinder block wall?
A. 3dB
B. 4dB
C. 6dB
D. 12dB
Answer: B
Most up-to-date testking 642-732:
Q56. Refer to the exhibit.
After performing a Layer 1 survey using Cisco Spectrum Expert, what is the result indicated
by the visual screen?
A. Normal 802.11b activity
B. Normal 802.11g activity
C. Microwave oven interference
D. Video camera interference
E. Bluetooth device interference
Answer: E
Q57. A customer wants to deploy wireless services inside a 500-seat auditorium. Given the volume of potential users in this condensed area, what is the best option for AP deployment?
A. place 802.11n APs along the outside edge with dual-band directional antennas
B. place 802.11n APs along the outside edge with 2.4GHz directional antennas
C. place 802.11n APs along the outside edge with 5GHz directional antennas
D. place 802.11n APs in the center with 2.4GHz sector antennas
E. place 802.11n APs in the center with 5GHz sector antennas
F. place 802.11n APs in the center with dual-band sector antennas
Answer: B
Q58. An engineer is conducting a failover test with a Mesh deployment by disconnecting the network interface of a RAP. A MAP becomes stranded even though it has an acceptable RSSI value on the link to its neighbor. What are two reasons the MAP may become stranded? (Choose two.)
A. the MAP is 6 hops away
B. the MAP is 9 hops away
C. the SNR on the neighbor link is 5dB
D. the SNR on the neighbor link is 15dB
E. the throughput on the neighbor link is 18Mbps
F. the throughput on the neighbor link is 24Mbps
Answer: B,C
Q59. Which option allows the maximum 2.4-GHz channel usage for a survey and data deployment in the ETSI domain?
A. 1, 6, 11
B. 1, 5, 9, 13
C. 1, 6, 9, 14
D. 1, 6, 11, 14
Answer: B
Q60. When using WCS 7.0 to calibrate a floor, is it more important to collect 50 or more distinct locations or to collect 150+ measurements?
A. 150+ measurements are more important than the locations because the information gathered is more granular.
B. Collecting 50 or more distinct locations is more important because this provides a wider coverage across the floor being calibrated.
C. Depending on the size of the floor 50+ distinct locations and 150+ measurements may provide divergent information that requires more data collection.
D. When calibrating a floor 50 or more distinct locations will yield 150+ measurements because multiple measurements are collected at each distinct location.
Answer: D