The actual examinees which read the Exambible Cisco 200-120 puts are good results regarding highly certified teachers, living a great existence. Exambible has been dedicated to build your long term secure and start your Cisco 200-120 CCNA Cisco Certified Network Associate CCNA (803) exam formulations from the most recent up to date Exambible checks 200-120 check motor. The goals can come accurate by commence your 200-120 vce for CCNA Cisco Certified Network Associate CCNA (803) exam via Exambible Cisco examine manuals just. Youll not capable of stand out your abilities in the very first endeavor regarding 200-120 check if you use any other pathway compared to Cisco. Cisco Cisco 200-120 pdf file will provide you with splendour therefore making you adequate certain about your entire existence.
2021 Nov vce 200-120:
Q101. - (Topic 4)
On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?
A. a router with subinterfaces configured on the physical interface that is connected to the switch
B. a router with an IP address on the physical interface connected to the switch
C. a switch with an access link that is configured between the switches
D. a switch with a trunk link that is configured between the switches
Answer: A
Q102. - (Topic 3)
An administrator must assign static IP addresses to the servers in a network. For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP properties box for the sales server?
A. IP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway: 192.168.20.9
B. IP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.20.1
C. IP address: 192.168.20.30 Subnet Mask: 255.255.255.248 Default Gateway: 192.168.20.25
D. IP address: 192.168.20.30 Subnet Mask: 255.255.255.240 Default Gateway: 192.168.20.17
E. IP address: 192.168.20.30 Subnet Mask: 255.255.255.240 Default Gateway: 192.168.20.25
Answer: C
Q103. - (Topic 9)
Which two types of NAT addresses are used in a Cisco NAT device? (Choose two.)
A. inside local
B. inside global
C. inside private
D. outside private
E. external global
F. external local
Answer: A,B
Q104. - (Topic 2)
Refer to the exhibit.
Which WAN protocol is being used?
A. ATM
B. HDLC
C. Frame Relay
D. PPP
Answer: C
Q105. - (Topic 1)
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?
A. This is a 10 Mb/s switch port.
B. This is a 100 Mb/s switch port.
C. This is an Ethernet port operating at half duplex.
D. This is an Ethernet port operating at full duplex.
E. This is a port on a network interface card in a PC.
Answer: C
Up to the minute dumps 200-120:
Q106. - (Topic 7)
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.
R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue?
A. R1 ethernetO/1 is shutdown. Configure no shutdown command.
B. R1 ethernetO/1 configured with a non-default OSPF hello interval of 25: configure no ip ospf hello-interval 25
C. R2 ethernetO/1 and R3 ethernetO/O are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25
D. Enable OSPF for R1 ethernetO/1; configure ip ospf 1 area 0 command under ethernetO/1
Answer: B
Q107. - (Topic 4)
Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: D,F
Q108. - (Topic 7)
What would be the effect of Issuing the command ip access-group 115 in on the s0/0/1 interface?
. No host could connect to RouterC through s0/0/1.
A. Telnet and ping would work but routing updates would fail.
B. FTP, FTP-DATA, echo, and www would work but telnet would fail.
C. Only traffic from the 10.4.4.0 network would pass through the interface.
Answer: A
Q109. - (Topic 5)
What are the Popular destinations for syslog messages to be saved? (Choose three)
A. Flash
B. The logging buffer .RAM
C. The console terminal
D. Other terminals
E. Syslog server
Answer: B,C,E
Q110. - (Topic 2)
What are three benefits of implementing VLANs? (Choose three.)
A. A higher level of network security can be reached by separating sensitive data traffic from other network traffic.
B. A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure.
C. A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
D. Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size.
E. Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size.
F. VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain.
G. Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.
Answer: A,C,D