It is more faster and easier to pass the Cisco 210-065 exam by using Accurate Cisco Implementing Cisco Video Network Devices v1.0 questuins and answers. Immediate access to the Far out 210-065 Exam and find the same core area 210-065 questions with professionally verified answers, then PASS your exam with a high score now.

2021 Feb cisco 210-065:

Q21. The command xCommand Security FIPSMode Activate is issued to a Cisco TelePresence C-Series codec. Management wants to reverse the effects of this command. Which two methods could be used for this purpose? (Choose two.) 

A. From the touch screen, disable FIPS mode in the Administrator Settings menu. 

B. From the touch screen, perform a factory reset from the Administrator Settings menu. 

C. From the touch screen, disable all security settings from the Administrator Settings menu. 

D. Use SSH to connect to the system and enter the xCommand Security FIPSMode Deactivate command. 

E. Use Telnet to connect to the system and enter the xCommand SystemUnit FactoryReset Init command. 

F. Use SSH to connect to the system and enter the xCommand SystemUnit FactoryReset Confirm: Yes command. 

Answer: B,F 


Q22. Refer to the exhibit. 

Management would like to find out when a particular multipoint control unit feature was enabled and who enabled it. Which menu option is the most appropriate when searching for that information? 

A. Event Display Filter 

B. Audit Log 

C. Event Log 

D. Syslog 

Answer: B 


Q23. An engineer needs to configure cascading to support additional video conference attendees. What are three capabilities when cascading? (Choose three.) 

A. Conductor automatically performs cascading. 

B. A maximum of four multipoint control units are supported. 

C. Cascading is supported for the Cisco TelePresence Server in remotely managed mode. 

D. It is possible to manually create a cascaded conference via the Cisco TelePresence MCU Management API. 

E. Cascading is supported for multipoint control units that are registered to Cisco Unified Communications Manager. 

F. All cascaded multipoint control units must be in the same location. 

Answer: A,C,D 


Q24. Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.) 

A. enhanced continuous presence 

B. active speaker switching 

C. continuous presence 

D. speaker switching 

E. room switching 

F. active continuous presence 

Answer: D,E 


Q25. A customer has a data and VoIP converged network and would like to add video to this network. Which two key QoS elements should be included in the new network design? (Choose two.) 

A. Configure bandwidth management features to smooth bursty traffic and mitigate end-to-end congestion. 

B. Assign a high priority to transactional traffic to maintain quality of business traffic. 

C. Keep video traffic on the low latency queue and move voice traffic to a lower-priority queue. 

D. Apply bandwidth control features that will guarantee bandwidth for the maximum possible amount of video traffic. 

E. Assign both video and voice traffic to use the highest-priority queue. 

Answer: A,D 


Renovate 210-065 civnd dumps:

Q26. An immersive video room requires acoustic remediation because there is noticeable reverb present. What type of acoustic paneling does Cisco recommend to provide remediation? 

A. NRC rating greater than 0.75 

B. NRC rating greater than 0.5 

C. NRC rating less than 0.75 

D. NRC rating less than 0.5 

Answer: A 


Q27. Which three products are compatible with Digital Media Manager? (Choose three.) 

A. Media Delivery Engine 

B. Interactive Experience Client 

C. Show and Share 

D. Cast 

E. Digital Signs 

F. Stadium Vision Director 

Answer: C,D,E 


Q28. Which two protocols can be used with the Cisco TelePresence Content Server to allow users to share content from their laptops? (Choose two.) 

A. BFCP 

B. H.239 

C. PCoIP 

D. Switched Presentation 

E. SCCP 

F. RDP 

Answer: A,B 


Q29. Which three features are supported by the Cisco Video Surveillance Encoding Server? (Choose three.) 

A. IP and analog cameras 

B. MPEG-2 and MPEG-4 encoding 

C. archiving 

D. motion detection 

E. clustering 

F. virtual matrix 

Answer: A,C,D 


Q30. Which CLI command can be used to reset the Cisco TelePresence System 500-32 personal video system to a factory condition? 

A. utils factory reset 2 

B. utils system factory init 

C. xcommand defaultvalues set level: 2 

D. xconfiguration default factory 

E. utils reset factory 

F. xcommand SystemUnit FactoryReset 

Answer: B