Cisco 100-101 exam dumps are created by Pass4sures superb professionals who have a great deal of experience in compiling the actual Cisco 100-101 exam demos. They are several kinds of Cisco 100-101 examination questions and answers that will appear within the real examination. A lot of candidates get passed the actual Cisco Cisco exam since we started. Pass4sure pledges you higher quality as well as great value which ensure you a passing score.

2016 Nov icnd1 book 100-101:

Q1. Refer to the exhibit. 

When running OSPF, what would cause router A not to form an adjacency with router B? 

A. The loopback addresses are on different subnets. 

B. The values of the dead timers on the routers are different. 

C. Route summarization is enabled on both routers. 

D. The process identifier on router A is different than the process identifier on router B. 

Answer:


Q2. Which command enables IPv6 forwarding on a Cisco router? 

A. ipv6 host 

B. ipv6 unicast-routing 

C. ipv6 local 

D. ipv6 neighbor 

Answer:


Q3. Refer to the exhibit. 

A company wants to use NAT in the network shown. Which commands will apply the NAT configuration to the proper interfaces? (Choose two.) 

A. R1(config)# interface serial0/1 R1(config-if)# ip nat inside 

B. R1(config)# interface serial0/1 R1(config-if)# ip nat outside 

C. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat inside 

D. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat outside 

E. R1(config)# interface serial0/1 R1(config-if)# ip nat outside source pool 200.2.2.18 255.255.255.252 

F. R1(config)# interface fastethernet0/0 R1(config-if)# ip nat inside source 10.10.0.0 255.255.255.0 

Answer: BC 


Q4. Refer to the exhibit. 

The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent? 

A. The network is likely to be congested, with the result that packets are being intermittently dropped. 

B. The branch router had to resolve the application server MAC address. 

C. There is a short delay while NAT translates the server IP address. 

D. A routing table lookup delayed forwarding on the first two ping packets. 

E. The branch router LAN interface should be upgraded to FastEthernet. 

Answer:


Q5. What is the best practice when assigning IP addresses in a small office of six hosts? 

A. Use a DHCP server that is located at the headquarters. 

B. Use a DHCP server that is located at the branch office. 

C. Assign the addresses by using the local CDP protocol. 

D. Assign the addresses statically on each node. 

Answer:


Most recent 100-101 ccna:

Q6. Scenario 

Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links. 

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices. 

R1 does not form an OSPF neighbor adjacency with R2. Which option would fix the issue? 

A. R1 ethernetO/1 is shutdown. Configure no shutdown command. 

B. R1 ethernetO/1 configured with a non-default OSPF hello interval of 25: configure no ip ospf hello-interval 25 

C. R2 ethernetO/1 and R3 ethernetO/O are configured with a non-default OSPF hello interval of 25; configure no ip ospf hello-interval 25 

D. Enable OSPF for R1 ethernetO/1; configure ip ospf 1 area 0 command under ethernetO/1 

Answer: B


Q7. Refer to the exhibit. 

How many collision domains are shown? 

A. one 

B. two 

C. three 

D. four 

E. six 

F. twelve 

Answer:


Q8. An administrator is working with the 192.168.4.0 network, which has been subnetted with a /26 mask. Which two addresses can be assigned to hosts within the same subnet? (Choose two.) 

A. 192.168.4.61 

B. 192.168.4.63 

C. 192.168.4.67 

D. 192.168.4.125 

E. 192.168.4.128 

F. 192.168.4.132 

Answer: CD 


Q9. What is the purpose of assigning an IP address to a switch? 

A. provides local hosts with a default gateway address 

B. allows remote management of the switch 

C. allows the switch to respond to ARP requests between two hosts 

D. ensures that hosts on the same LAN can communicate with each other 

Answer:


Q10. What is the purpose of the switchport command? 

Switch(config-if)# switchport port-security maximum 1 Switch(config-if)# switchport port-security mac-address 0018.DE8B.4BF8 

A. It ensures that only the device with the MAC address 0018.DE8B.4BF8 will be able to connect to the port that is being configured. 

B. It informs the switch that traffic destined for MAC address 0018.DE8B.4BF8 should only be sent to the port that is being configured. 

C. It will act like an access list and the port will filter packets that have a source or destination MAC of 0018.DE8B.4BF8. 

D. The switch will shut down the port of any traffic with source MAC address of 0018.DE8B.4BF8. 

Answer: