Want to know Pass4sure 100-101 Exam practice test features? Want to lear more about Cisco CCNA Interconnecting Cisco Networking Devices 1 (ICND1) certification experience? Study Accurate Cisco 100-101 answers to Replace 100-101 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 100-101 (CCNA Interconnecting Cisco Networking Devices 1 (ICND1)) test on your first attempt.
2021 Jan 100-101 exam fee:
Q91. Refer to the exhibit.
A network administrator has configured a Catalyst 2950 switch for remote management by pasting into the console the configuration commands that are shown in the exhibit. However, a Telnet session cannot be successfully established from a remote host. What should be done to fix this problem?
A. Change the first line to interface fastethernet 0/1.
B. Change the first line to interface vlan 0/1.
C. Change the fifth line to ip default-gateway 192.168.17.241.
D. Change the fifth line to ip route 0.0.0.0 0.0.0.0 192.168.17.1.
E. Change the sixth line to line con 0.
Answer: C
Q92. Refer to the exhibit.
The ports that are shown are the only active ports on the switch. The MAC address table is shown in its entirety. The Ethernet frame that is shown arrives at the switch.
What two operations will the switch perform when it receives this frame? (Choose two.)
A. The MAC address of 0000.00aa.aaaa will be added to the MAC address table.
B. The MAC address of 0000.00dd.dddd will be added to the MAC address table.
C. The frame will be forwarded out port fa0/3 only.
D. The frame will be forwarded out fa0/1, fa0/2, and fa0/3.
E. The frame will be forwarded out all the active ports.
Answer: AD
Q93. Refer to the graphic.
R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Answer: DF
Q94. Refer to the exhibit.
SwitchA receives the frame with the addressing shown. According to the command output also shown in the exhibit, how will SwitchA handle this frame?
A. It will drop the frame.
B. It will forward the frame out port Fa0/6 only.
C. It will flood the frame out all ports.
D. It will flood the frame out all ports except Fa0/3.
Answer: D
Q95. How many simultaneous Telnet sessions does a Cisco router support by default?
A. 1
B. 2
C. 3
D. 4
E. 5
F. 6
Answer: E
Renew ccent 100-101 vs 640-822:
Q96. Refer to the exhibit.
Host A can communicate with Host B but not with Hosts C or D. How can the network administrator solve this problem?
A. Configure Hosts C and D with IP addresses in the 192.168.2.0 network.
B. Install a router and configure a route to route between VLANs 2 and 3.
C. Install a second switch and put Hosts C and D on that switch while Hosts A and B remain on the original switch.
D. Enable the VLAN trunking protocol on the switch.
Answer: B
Q97. Which command is used to display the collection of OSPF link states?
A. show ip ospf link-state
B. show ip ospf lsa database
C. show ip ospf neighbors
D. show ip ospf database
Answer: D
Q98. Which IP addresses are valid for hosts belonging to the 10.1.160.0/20 subnet? (Choose three.)
A. 10.1.168.0
B. 10.1.176.1
C. 10.1.174.255
D. 10.1.160.255
E. 10.1.160.0
F. 10.1.175.255
Answer: ACD
Q99. What is the default administrative distance of the OSPF routing protocol?
A. 90
B. 100
C. 110
D. 120
E. 130
F. 170
Answer: C
Q100. Which of the following IP addresses are valid Class B host addresses if a default Class B
mask is in use? (Choose two.)
A. 10.6.8.35
B. 133.6.5.4
C. 192.168.5.9
D. 127.0.0.1
E. 190.6.5.4
Answer: BE