It is more faster and easier to pass the Cisco 200-125 exam by using Guaranteed Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) questuins and answers. Immediate access to the Renovate 200-125 Exam and find the same core area 200-125 questions with professionally verified answers, then PASS your exam with a high score now.

2021 Dec 200-125 free draindumps

Q81. - (Topic 8) 

Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link? 

A. show frame-relay lmi 

B. show frame-relay map 

C. show frame-relay pvc 

D. show interfaces serial 

Answer:


Q82. - (Topic 3) 

What is known as "one-to-nearest" addressing in IPv6? 

A. global unicast 

B. anycast 

C. multicast 

D. unspecified address 

Answer:


Q83. - (Topic 9) 

Which command can you use to set the hostname on a switch? 

A. switch-mdf-c1(config)#hostname switch-mdf1 

B. switch-mdf-c1>hostname switch-mdf1 

C. switch-mdf-c1#hostname switch-mdf1 

D. switch-mdf-c1(config-if)#hostname switch-mdf1 

Answer:


Q84. CORRECT TEXT - (Topic 7) 

Central Florida Widgets recently installed a new router in their office. Complete the network installation by performing the initial router configurations and configuring R1PV2 routing using the router command line interface (CLI) on the RC. 

Configure the router per the following requirements: 

Name of the router is R2 

Enable. secret password is cisco 

The password to access user EXEC mode using the console is cisco2 

The password to allow telnet access to the router is cisco3 

IPV4 addresses mast be configured as follows: 

Ethernet network 209.165.201.0/27 - router has fourth assignable host address in subnet 

Serial network is 192.0.2.176/28 - router has last assignable host address in the subnet. 

Interfaces should be enabled. 

Router protocol is RIPV2 

Attention: 

In practical examinations, please note the following, the actual information will prevail. 

1. Name or the router is xxx 

2. EnablE. secret password is xxx 

3. Password In access user EXEC mode using the console is xxx 

4. The password to allow telnet access to the router is xxx 

5. IP information 

Answer: Router>enable 

Router#config terminal 

Router(config)#hostname R2 

R2(config)#enable secret Cisco 1 

R2(config)#line console 0 

R2(config-line)#password Cisco 2 

R2(config-line)#exit 

R2(config)#line vty 0 4 

R2(config-line)#password Cisco 3 

R2(config-line)#login 

R2(config-line)#exit 

R2(config)#interface faO/0 

R2(config-if)#ip address 209.165.201.4 255.255.255.224 

R2(config)#interface s0/0/0 

R2(config-if)#ip address 192.0.2.190 255.255.255.240 

R2(config-if)#no shutdown 

R2(config-if)#exit 

R2(config)#router rip 

R2(config-router)#version 2 

R2(config-router)#network 209.165.201.0 

R2(config-router)#network 192.0.2.176 

R2(config-router)#end 

R2#copy run start 


Q85. - (Topic 6) 

Refer to the exhibit. 

Statements A, B, C, and D of ACL 10 have been entered in the shown order and applied to interface E0 inbound, to prevent all hosts (except those whose addresses are the first and last IP of subnet 172.21.1.128/28) from accessing the network. But as is, the ACL does not restrict anyone from the network. How can the ACL statements be re-arranged so that the system works as intended? 

A. ACDB 

B. BADC 

C. DBAC 

D. CDBA 

Answer:


Most up-to-date 200-125 practice exam:

Q86. - (Topic 4) 

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router? 

A. 2 

B. 8 

C. 16 

D. unlimited 

Answer:


Q87. - (Topic 5) 

Which three are the components of SNMP? (Choose three) 

A. MIB 

B. SNMP Manager 

C. SysLog Server 

D. SNMP Agent 

E. Set 

Answer: A,B,D 


Q88. - (Topic 9) 

If a router has four interfaces and each interface is connected to four switches, how many broadcast domains are present on the router? 

A. 1 

B. 2 

C. 4 

D. 8 

Answer:


Q89. - (Topic 2) 

VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan 3 command in interface configuration mode? 

A. The command is rejected. 

B. The port turns amber. 

C. The command is accepted and the respective VLAN is added to vlan.dat. 

D. The command is accepted and you must configure the VLAN manually. 

Answer:


Q90. - (Topic 5) 

What command instructs the device to timestamp Syslog debug messages in milliseconds? 

A. service timestamps log datetime localtime 

B. service timestamps debug datetime msec 

C. service timestamps debug datetime localtime 

D. service timestamps log datetime msec 

Answer: