You can save much more time in case you utilize our Cisco 200-125 study guide. To put it another method, you dont have to spend much time in reading individuals lengthy books. Each of our Cisco Cisco 200-125 dumps also contain a lot of wonderful simulated questions. The simulated questions tend to be merged into the 200-125 questions as well as answers of our Cisco 200-125 study guides. Its extremely convenient to suit your needs to make the exam together with our incredible 200-125 materials. All of us make sure that you will definitely obtain success so long as you place pace together with our Cisco certification review materials. Naturally, you should use a vast knowledge about the course firstly. The much more you review the 200-125 review materials, the nearer to your destination. The particular Cisco 200-125 books or the eBooks tend to be portable, so you can consider them wherever and anytime you desire. You have the access towards the Cisco study guide for added assistance. We assure the consumers absolute achievement due to ultimate, authentic as well as excellent supplies.

2021 Dec 200-125 training

Q151. - (Topic 9) 

Which type of address is the public IP address of a NAT device? 

A. outside global 

B. outside local 

C. inside global 

D. inside local 

E. outside public 

F. inside public 

Answer:


Q152. - (Topic 1) 

Refer to the exhibit. 

After HostA pings HostB, which entry will be in the ARP cache of HostA to support this transmission? 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

E. Exhibit E 

F. Exhibit F 

Answer:


Q153. - (Topic 4) 

Refer to the exhibit. 

What can be determined about the router from the console output? 

A. No configuration file was found in NVRAM. 

B. No configuration file was found in flash. 

C. No configuration file was found in the PCMCIA card. 

D. Configuration file is normal and will load in 15 seconds. 

Answer:


Q154. - (Topic 9) 

Which three commands can you use to set a router boot image? (Choose three.) 

A. Router(config)# boot system flash c4500-p-mz.121-20.bin 

B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin 

C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin 

D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin 

E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin 

F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin 

Answer: A,B,C 


Q155. DRAG DROP - (Topic 7) 

Answer: 


Most recent 200-125 exams:

Q156. - (Topic 1) 

Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.) 

A. Spanning Tree Protocol allows switches to automatically share VLAN information. 

B. Establishing VLANs increases the number of broadcast domains. 

C. Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information. 

D. Microsegmentation decreases the number of collisions on the network. 

E. In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port. 

F. If a switch receives a frame for an unknown destination, it uses ARP to resolve the address. 

Answer: B,D,E 


Q157. - (Topic 5) 

Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.) 

A. Set the IP gateway to be used by the network. 

B. Perform host discovery used DHCPDISCOVER message. 

C. Configure IP address parameters from DHCP server to a host. 

D. Provide an easy management of layer 3 devices. 

E. Monitor IP performance using the DHCP server. 

F. Assign and renew IP address from the default pool. 

Answer: C,F 


Q158. - (Topic 9) 

What is the first step in the NAT configuration process? 

A. Define inside and outside interfaces. 

B. Define public and private IP addresses. 

C. Define IP address pools. 

D. Define global and local interfaces. 

Answer:


Q159. - (Topic 6) 

Refer to the exhibit. 

A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands. 

Which two of these changes are necessary for SwitchA to meet the requirements? (Choose two.) 

A. Port security needs to be globally enabled. 

B. Port security needs to be enabled on the interface. 

C. Port security needs to be configured to shut down the interface in the event of a violation. 

D. Port security needs to be configured to allow only one learned MAC address. 

E. Port security interface counters need to be cleared before using the show command. 

F. The port security configuration needs to be saved to NVRAM before it can become active. 

Answer: B,D 


Q160. - (Topic 5) 

What are three benefits of GLBP? (Choose three.) 

A. GLBP supports up to eight virtual forwarders per GLBP group. 

B. GLBP supports clear text and MD5 password authentication between GLBP group members. 

C. GLBP is an open source standardized protocol that can be used with multiple vendors. 

D. GLBP supports up to 1024 virtual routers. 

E. GLBP can load share traffic across a maximum of four routers. 

F. GLBP elects two AVGs and two standby AVGs for redundancy. 

Answer: B,D,E