we provide Downloadable Cisco route 300 101 torrent which are the best for clearing 300 101 route pdf test, and to get certified by Cisco ROUTE Implementing Cisco IP Routing. The ccnp route 300 101 pdf Questions & Answers covers all the knowledge points of the real 300 101 dumps exam. Crack your Cisco 300 101 route Exam with latest dumps, guaranteed!


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 300-101 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/300-101-exam-dumps.html

P.S. Downloadable 300-101 practice exam are available on Google Drive, GET MORE: https://drive.google.com/open?id=1IPFRgHPm2o-6qCPBhQuk3ypuFkiGdV3b


New Cisco 300-101 Exam Dumps Collection (Question 10 - Question 19)

Q1. When policy-based routing (PBR) is being configured,

Which three criteria can the set command specify? (Choose three.)

A. all interfaces through which the packets can be routed

B. all interfaces in the path toward the destination

C. adjacent next hop router in the path toward the destination

D. all routers in the path toward the destination

E. all networks in the path toward the destination

F. type of service and precedence in the IP packets

Answer: A,C,F

Explanation:

Configuring Policy-Based Routing (PBR):

You can configure PBR by following these steps. Some of the steps may be omitted depending on your application for PBR. For this example, note the set condition options listed is step 3 (answers are bolded).

Step1

Define and configure the route map needed for the policy. This is accomplished with the route-map command, as discussed previously.

Step2

Define and configure the match statements the route map will use. The most common

match statements used are the following: match ip address [access-list number]

The match ip address is used to call a standard, extended, or expanded-range ACL. match length [min_packet_length_0-2147483647] [max_packet_length_0-2147483647]

The match length is used to match the Layer 3 packet length, in bytes, with all associated headers and trailers included. You must enter the minimum and maximum packet length. Use the match length command to policy route traffic based on packet size. You can deploy this to route traffic with large or small packet sizes to specific areas of the network. Step3

Configure and define the new routing policy with set commands. Multiple set commands may be used; if multiple commands are used, they are executed in the following order:

set ip {precedence [value_0-7 | name] | tos [value_0-8 | name]} set ip next-hop ip_address

set interface interface_name

set ip default next-hop ip_address set default interface interface_name

Set ip precedence {[1-7]|[routine|critical|flash|flash- override|immediate|internet|network|priority]}



Q2. Which statement about stateless and stateful IPv6 autoconfiguration are true?

A. Both stateless and stateful autoconfiguration require additional setup

B. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration requires additional setup

C. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires no additional setup

D. Both stateless and stateful autoconfiguration require no additional setup

Answer: B



Q3. Refer to the exhibit.

Which statement is correct regarding the operation of NAT-PT between the IPv4 and IPv6 networks shown?

A. The router will determine the IPv4 destination address.

B. The source IPv6 host can use DNS to determine the IPv6-to-IPv4 address mapping.

C. The host is statically configured with the IPv6-to-IPv4 address mapping.

D. ICMP can be used to determine the IPv6-to-IPv4 address mapping.

Answer: B



Q4. Which two OSPF router types can perform summarize in an OSPF network? (Choose two)

A. summary router

B. area border router

C. autonomous system boundary router

D. internal router

E. backbone router

Answer: B,C



Q5. You have been asked to evaluate how EIGRP is functioning in a customer network.

What is the advertised distance for the 192.168.46.0 network on R1?

A. 333056

B. 1938688

C. 1810944

D. 307456

Answer: A



Q6. What is the function of the snmp-server enable traps and snmp-server host 192.168.1.3 trap version 1c public commands?

A. to allow only 192.168.1.3 to access the system using the community-string public.

B. to collect information about the system on a network management server.

C. to disable all SNMP informs that are on the system

D. to allow private communications between the router and the host.

Answer: A



Q7. Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)

A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.

B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.

C. The device can establish a point-to-point connection to the cloud without a DLCI.

D. They can operate normally without a DLCI map.

E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

Answer: A,B



Q8. Which two types of authentication does EIGRP offer? (Choose two)

A. TKIP

B. MD5

C. WPA

D. Plain text

Answer: B,D

Explanation: The router uses two types of authentication:

u2711 Simple password authentication (also called plain text authentication)u2014Supported by Integrated System-Integrated System (IS-IS), Open Shortest Path First (OSPF), and Routing Information Protocol Version 2 (RIPv2)

u2711 MD5 authenticationu2014Supported by OSPF, RIPv2, BGP, and EIGRP



Q9. You have been asked to evaluate how EIGRP is functioning in a customer network.

What type of route filtering is occurring on R6

A. Distribute-list using an ACL

B. Distribute-list using a prefix-list

C. Distribute-list using a route-map

D. An ACL using a distance of 255

Answer: A



Q10. Observe the exhibit.

If the command variance 3 were added to RTE, which path or paths would be chosen to route traffic to network X?

A. E-B-A

B. E-B-A and E-C-A

C. E-C-A and E-D-A

D. E-B-A, E-C-A and E-D-A

Answer: B

Explanation:

Advertised distance of RTD is greater than FD of RTE-RTC-RTA, so the route through D will not be used.



P.S. Easily pass 300-101 Exam with 2passeasy Downloadable Dumps & pdf vce, Try Free: https://www.2passeasy.com/dumps/300-101/ (436 New Questions)