Act now and download your Cisco ccnp 300 101 test today! Do not waste time for the worthless Cisco 300 101 pdf tutorials. Download Most recent Cisco ROUTE Implementing Cisco IP Routing exam with real questions and answers and begin to learn Cisco ccnp 300 101 dumps with a classic professional.


♥♥ 2021 NEW RECOMMEND ♥♥

Free VCE & PDF File for Cisco 300-101 Real Exam (Full Version!)

★ Pass on Your First TRY ★ 100% Money Back Guarantee ★ Realistic Practice Exam Questions

Free Instant Download NEW 300-101 Exam Dumps (PDF & VCE):
Available on: http://www.surepassexam.com/300-101-exam-dumps.html

P.S. Free 300-101 braindump are available on Google Drive, GET MORE: https://drive.google.com/open?id=1VVsMJd1T1ylej0aePOIREXo7V31c7pn0


New Cisco 300-101 Exam Dumps Collection (Question 12 - Question 21)

Question No: 12

CORRECT TEXTROUTE.com is a small IT corporation that has an existing enterprise network that is running IPv6 0SPFv3. Currently OSPF is configured on all routers. However, R4's loopback address (FEC0:4:4) cannot be seen in R1's IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OPSF features and does not change the current area assignments. You will know that you have corrected the fault when R4's loopback address (FEC0:4:4) can be seen in RTs IPv6 routing table.

Special Note: To gain the maximum number of points you must remove all incorrect or unneeded configuration statements related to this issue.

Answer:

Here is the solution below:

Explanation:

To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more attention to the outputs of routers R2 and R3 The output of the "show running-config" command of R2:

The output of the "show running-config" command of R3:

We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a virtual link to connect to the backbone through a non-backbone area. The area through which you configure the virtual link is known as a transit area. In this case, the area 11 will become the transit area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual-link <neighbor router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the OSPF process ID of R2 is 1):

R2>enable R2#configure terminal

R2(config)#ipv6 router ospf 1

R2(config-rtr)#area 11 virtual-link 3.3.3.3 Save the configuration:

R2(config-rtr)#end

R2#copy running-config startup-config

(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):

R3>enable R3#configure terminal

R3(config)#ipv6 router ospf 1

R3(config-rtr)#no area 54 virtual-link 4.4.4.4

R3(config-rtr)#area 11 virtual-link 2.2.2.2 Save the configuration:

R3(config-rtr)#end

R3#copy running-config startup-config

You should check the configuration of R4, too. Make sure to remove the incorrect configuration statements to get the full points.

R4(config)#ipv6 router ospf 1

R4(config-router)#no area 54 virtual-link 3.3.3.3 R4(config-router)#end

After finishing the configuration doesnu2021t forget to ping between R1 and R4 to make sure they work.

Note. If you want to check the routing information, use the show ipv6 route command, not "show ip route".


Question No: 13

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network. Which of the following answers best describes the routeru2021s logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?

A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel gre acl command under the incoming interface

B. When routing the packet, matching a route whose outgoing interface is theGRE tunnel interface

C. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interface

D. When permitted by an ACL that was referenced in the associated crypto map

Answer: B

Explanation:

As for the correct answer, the process of routing a packet out a GRE tunnel interface triggers the GRE encapsulation action. As for the incorrect answers: There is no tunnel gre acl command. There is no IPsec tunnel interface. Finally, one answer refers to logic that would describe a routeru2021s logic when determining whether to encapsulate a packet into an IPsec tunnel.


Question No: 14

Which cisco Express Forwarding component maintains Layer 2 addressing information?

A. dCEF

B. adjacency table.

C. FIB

D. fast switching

E. RIB

Answer: B

Explanation: Adjacency TablesNodes in the network are said to be adjacent if they can reach each other with a single hop across a link layer. In addition to the FIB, CEF uses adjacency tables to prepend Layer 2 addressing information. The adjacency table maintains Layer 2 next-hop addresses for all FIB entries. http://www.cisco.com/c/en/us/td/docs/ios/12_2/switch/configuration/guide/fswtch_c/xcfcef.ht ml


Question No: 15

An EUI-64 bit address is formed by inserting which 16-bit value into the MAC address of a device?

A. 3FFE

B. FFFE

C. FF02

D. 2001

Answer: B


Question No: 16

PPPoE is composed of which two phases?

A. Active Authentication Phase and PPP Session Phase

B. Passive Discovery Phase and PPP Session Phase

C. Active Authorization Phase and PPP Session Phase

D. Active Discovery Phase and PPP Session Phase

Answer: D


Question No: 17

Which three characteristics are shared by subinterfaces and associated EVNs? (Choose three.)

A. IP address

B. routing table

C. forwarding table

D. access control lists

E. NetFlow configuration

Answer: A,B,C

Topic 5, Infrastructure Security

53.For troubleshooting purposes, which method can you use in combination with the u201cdebug ip packetu201d command to limit the amount of output data?

A. You can disable the IP route cache globally.

B. You can use the KRON scheduler.

C. You can use an extended access list.

D. You can use an IOS parser.

E. You can use the RITE traffic exporter.


Question No: 18

Which three statements about SNMP are true? (Choose Three)

A. The manager configures and send traps to the agent.

B. The manager sends GET and SET messages.

C. SNMPv3 supports authentication and encryption.

D. The manager polls the agent using UDP port 161

E. The MIB database can be altered only by the SNMP agent.

F. The agent is the monitoring device.

Answer: C,D,F


Question No: 19

Which command denies the default route?

A. ip prefix-list deny-route seq 5 deny 0.0.0.0/32

B. ip prefix-list deny-route seq 5 deny 0.0.0.0/8

C. ip prefix-list deny-route seq 5 deny 0 0 0.0/0

D. ip prefix-list deny-route seq 5 deny 0.0.0.0/16

Answer: C


Question No: 20

A network administrator uses GRE over IPSec to connect two branches together via VPN tunnel. Which one of the following is the reason for using GRE over IPSec?

A. GRE over IPSec provides better QoS mechanism and is faster than other WAN technologies.

B. GRE over IPSec decreases the overhead of the header.

C. GRE supports use of routing protocol, while IPSec supports encryption.

D. GRE supports encryption, while IPSec supports use of routing protocol.

Answer: C


Question No: 21

If you convert a WAN connection with OSPF from T1 to a Frame Relay circuit, which two actions must you take to enable the connection? (Choose two)

A. Change the OSPF network type to nonbroadcast.

B. Manually configure neighbors in the OSPF process.

C. Manually configure the hello and dead timers.

D. Change the OSPF network type to broadcast.

E. Change the OSPF network type to multipoint nonbroadcast.

Answer: A,B


100% Most recent Cisco 300-101 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/300-101-dumps.html (New 436 Q&As)